The Ferrite Ring Combo Pack is a convenient solution for troubleshooting RFI/EMI from unknown frequencies or multiple frequencies that require multiple suppression mixes. Included in this combo pack are ten 1.4″ OD/.9″ ID ring toroids as follows: Mix 77 effective from .1-50 MHz including AM Broadcast band – quantity: 5 Mix 43 effective from 25-250 MHz for general purpose – quantity: 5 Mix 61 effective from 200-2000 MHz for cell phone, WIFI, HDTV, Cable TV interference – quantity: 5 The ring toroids are useful for AC/DC common mode choking with multiple turns as shown below AC Cable on F-240 Toroid – 7 turns DC Cable on F240 – 4 turns The ring toroids can also be used on coax or signal lines as shown below: RG58 12 turns on FT240 Ethernet Cable on F-240 Toroid – 7 turns For RFI/EMI wrap as many turns as possible for higher choking (under 30 MHz). For over 30 MHz, 1-3 turns is usually sufficient due the to capacitive effect of multiple turns reducing choking effect.
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.