Buy DIRECT, on eBay or at Ham Radio Outlet stores nationwide, HRO Product List HERE QUICK and EASY RFI Solutions for Consumer Electronics - FREE RFI Tip Sheet
Palomar Engineers will be at the Mabuhay DX Group Meeting on April 19-21 and will have product display and a group presentation on eliminating RFI and using Multi-Band Antennas to work more DX!
NEW PRODUCT ALERT
BULLET™ END FED ANTENNAS - 80-6 Meter - 100/500/1500 Watts
SHORTER, SAFER, MORE BANDS THAN EFHW
Bullet end fed antennas are shorter than conventional dipoles, yet deliver superior performance on many bands using the radiating coax as part of the antenna. They come in a variety of power levels, and work great for portable or permanent installations. Thousands in use world-wide! Selected models available at Ham Radio Outlet and all available on company website where full details on these antennas and many accessories are shown.
BULLET-2006 Antenna (Click for more info)
BULLET-4006 Antenna (Click for more info)
BULLET-8006 Antenna (click for more info)
Palomar Engineers Antenna Info Sheet
Popular Categories
HF Wire Antennas - End Feds, Off Center Fed, Loop, T2FD/BBTD, Dipoles and Zepps, 160-6 Meters, Wire, Hardware and Instructions for you.
Ferrite Products - Rings, Snap On, Slip On, useful from 150KHz - 2 GHZ, Mixs 31, 43, 52, 61, 75
RFI Solutions - Consumer Electronics, Computer, Audio/Home Theater, Wall Warts, Solar and more!
Baluns/Ununs/Chokes (1:1-81:1 ratios) for RX, 100/500/1500/5000 Watts including Hybrids (with choke) and Multi-Ratio
Radio Transceiver/Linear Amplifier RFI Kits - All Brands, VLF, HF to UHF
Noise Filters - Coax, AC and DC power 100 KHz - 150 MHz, up to -48 dB noise suppression - hear DX again!
Palomar Engineers® products are over engineered to outperform the competition without being over priced!
Featured Products
$79.95
$55.95
$155.00
$108.00
$55.00
$100.00
$49.95
$112.00
$199.95
$279.95
$359.95
$189.95
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.