End Fed OCF Antennas
Off Center Fed (OCF) antennas are very convenient as they will allow multiple bands of operation with a simple wire antenna which is fed off center. For example, the Palomar Engineers 4010 OCF is a very popular antenna and consists of an off center fed dipole with sides of 55 feet and 11 feet and it will work all bands from 40-6 meters.The End Fed OCF uses the same dimensions but the wire section is 55 feet as in the OCF and the coax outer braid is used for the “other” short side of the OCF dipole. We place a choke on the coax at the 12 foot distance from the matching unit and we essentially have an OCF antenna with its great frequency range, but with only a 55 foot wire length instead of the 66 feet required by the regular OCF. You feed the antenna from one end which may be more convenient for some installations. This antenna will work on 40-30-20-17-15-12-10 and 6 meters. Most bands are under 3:1 SWR and easily tuned by your transceiver’s internal antenna tuner or external tuner used with an amplifier. (see BULLET-4006 for specific details and SWR curves).
These antennas are MUCH BETTER PERFORMERS than End Fed Half Wave antennas because they work the WARC bands, DO NOT HAVE A DANGEROUS HIGH VOLTAGE at the antenna connection and are SHORTER to fit in smaller spaces yet provide more band coverage up to 6 meters!
End Fed OCF Antennas
Off Center Fed (OCF) antennas are very convenient as they will allow multiple bands of operation with a simple wire antenna which is fed off center. For example, the Palomar Engineers 4010 OCF is a very popular antenna and consists of an off center fed dipole with sides of 55 feet and 11 feet and it will work all bands from 40-6 meters.The End Fed OCF uses the same dimensions but the wire section is 55 feet as in the OCF and the coax outer braid is used for the “other” short side of the OCF dipole. We place a choke on the coax at the 12 foot distance from the matching unit and we essentially have an OCF antenna with its great frequency range, but with only a 55 foot wire length instead of the 66 feet required by the regular OCF. You feed the antenna from one end which may be more convenient for some installations. This antenna will work on 40-30-20-17-15-12-10 and 6 meters. Most bands are under 3:1 SWR and easily tuned by your transceiver’s internal antenna tuner or external tuner used with an amplifier. (see BULLET-4006 for specific details and SWR curves).
These antennas are MUCH BETTER PERFORMERS than End Fed Half Wave antennas because they work the WARC bands, DO NOT HAVE A DANGEROUS HIGH VOLTAGE at the antenna connection and are SHORTER to fit in smaller spaces yet provide more band coverage up to 6 meters!
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer