CUBE 1:1 Feed Line Choke Balun, 1.5KW, 1.8-61 MHz Eyebolt Version - DipolesProduct DetailsBrand: Palomar EngineersEffective Frequency Range (MHz): 1-61 MHzPEP Power Rating (watts): 1500Common Mode Attenuation (db): up to -38 dBEstimated Insertion Loss (db): .10Input Connector Type: SO-239 femaleOutput Connector Connector Type: side eyebolts and top halyard hoistEnclosure Size (LxWxH inches): 4 x 4 x 21500 Watt PEP Rated 1:1 CUBE™ Balun for dipoles
* Help keep RF out of the shack.
* Provides maximum transfer of RF to the antenna.
* Suppress radiation from the feeder cable
* Makes the antenna radiation pattern predictable.
* Outperforms the competition by 24 dB common mode rejection! (see graphs)
* Reduces QRN and TVI to the neighbors.
The CB-1-1500 balun is useful as common mode feed line chokes or unbalanced coax to balanced antenna interface. SO-239 input to side terminal/eyebolt output. . Rated 1500 Watts PEP from 1-61 MHz. Common mode rejection up to -38dB over the frequency range. The CB-1-1500 is the balun version and the CU-1-1500 is the unun version (coax in and coax out).
Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid. Much more effective then our snap on ferrite beads as this balun which provides a higher choking impedance over a broad frequency range.
For most effective results, use another feed line choke (coax noise filter) at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid acting as secondary receive antenna
1500 Watt PEP Rated 1:1 CUBE™ Balun for dipoles
* Help keep RF out of the shack.
* Provides maximum transfer of RF to the antenna.
* Suppress radiation from the feeder cable
* Makes the antenna radiation pattern predictable.
* Outperforms the competition by 24 dB common mode rejection! (see graphs)
* Reduces QRN and TVI to the neighbors.
The CB-1-1500 balun is useful as common mode feed line chokes or unbalanced coax to balanced antenna interface. SO-239 input to side terminal/eyebolt output. . Rated 1500 Watts PEP from 1-61 MHz. Common mode rejection up to -38dB over the frequency range. The CB-1-1500 is the balun version and the CU-1-1500 is the unun version (coax in and coax out).
Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid. Much more effective then our snap on ferrite beads as this balun which provides a higher choking impedance over a broad frequency range.
For most effective results, use another feed line choke (coax noise filter) at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid acting as secondary receive antenna
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer