50:200 (4:1) CUBE™ Voltage Balun, 1.8-61 MHz, 1.5KW - Carolina Windom, OCF, Loop AntennasProduct DetailsMPN: CB-4-1500Country/Region of Manufacture: USAType: BalunInput ohms/Output ohms: 50 in, 200 outFrequency Range < 2:1 SWR (MHz): 1-31PEP Power Rating (watts): 1500Enclosure Size: 4" x4" x 2"Weight (pounds): 2Antenna Compatability: Dipoles: Extended double zepp, folded 2 wire, off center fed (OCF); Loops: Horizontal, vertical - coax fedAfter many requests we have created a compact, special balun for OCF antennas with vertical radiators. The CB-4-1500ODCV is a CUBE™ enclosure containing a dual core, bifilar wound, voltage balun to force equal voltages on the unequal sides of the off center fed antenna and force current down to the vertical radiator so it acts like a vertical antenna adding to the radiation pattern at low angles for DX.
The vertical radiator is typically 10 feet of 50 ohm coax for the 40 meter long (67 feet at the top) and 22 feet long for the 135 foot OCF.At the bottom of the vertical radiator you should have a line isolator or 1:1 balun (such as the Palomar BA-8E or BA-58E sleeve balun, or CB-1-1500 cube balun) to stop the current on the outside braid of the coax from using the rest of your feedline back to the radio as a long vertical radiator causing RFI and other problems as well as skewing the radiation pattern. The balun can be used with any size.
The balun is rated for full 1500 watts PEP from 1.8Mhz – 61 Mhz and usable to over 150 MHZ! (see graph) The balun can be used with either a 50 or 75 ohm coax vertical radiator and feedline.
The matching line isolator is the MC-1-3000 which should be used at the end of the vertical radiator.
On Sale
RG-8X Coax cable with PL-259's on each end - 50 feetRG-8X Coax cable with PL-259's on each end - 50 feetSKU RG-8X-50List price $79.95 Save 13%$69.95
After many requests we have created a compact, special balun for OCF antennas with vertical radiators. The CB-4-1500ODCV is a CUBE™ enclosure containing a dual core, bifilar wound, voltage balun to force equal voltages on the unequal sides of the off center fed antenna and force current down to the vertical radiator so it acts like a vertical antenna adding to the radiation pattern at low angles for DX.
The vertical radiator is typically 10 feet of 50 ohm coax for the 40 meter long (67 feet at the top) and 22 feet long for the 135 foot OCF.At the bottom of the vertical radiator you should have a line isolator or 1:1 balun (such as the Palomar BA-8E or BA-58E sleeve balun, or CB-1-1500 cube balun) to stop the current on the outside braid of the coax from using the rest of your feedline back to the radio as a long vertical radiator causing RFI and other problems as well as skewing the radiation pattern. The balun can be used with any size.
The balun is rated for full 1500 watts PEP from 1.8Mhz – 61 Mhz and usable to over 150 MHZ! (see graph) The balun can be used with either a 50 or 75 ohm coax vertical radiator and feedline.
The matching line isolator is the MC-1-3000 which should be used at the end of the vertical radiator.
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer