Use for 1″ Cable – RG218, etc.
For 1” cables use five split beads for 80-10 meters (3-30 MHz) or ten split beads for 160-10 (1.8-30 MHz) meters or use 15 for even higher choking for 1-10 MHz. For 144 MHz use only 4 beads as they will provide > 500 ohms. Typical common mode suppression is -9 to 30 dB depending upon the number of beads and frequency. Quite often 20 dB is considered the minimum effective reduction.
Typical Impedance per split bead: 10 MHz: 90 ohms, 25 MHz: 156 ohms, 100 MHz: 250 ohms, 250 MHz: 305 ohms
A minimum impedance of 500 ohms is needed for 50 ohm cable or 10 times the cable impedance for other cables to make a measurable difference in common mode current suppression.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
Note: Ferrite beads may be hexagonal or square shape depending on inventory on hand at time of order.
Due to many requests for antenna static bleeders, we have developed a product line of static bleeders for coax and for ladder line applications. Static electricity is caused by many situations including high desert wind, atmospheric conditions, etc. You may hear static crashes or have a buildup of static electricity that my be annoying during a radio conversation and it may be harmful to solid state electronics if high voltages are present on the RF input to your equipment.
A static “Bleeder” which shorts the direct static voltage to ground while leaving the RF frequency voltage unaffected if very beneficial particularly to those operations in desert conditions where low humidity, high static buildup are quite common. The SB-1 and SB-2 coax static bleeders work on coax line and the SB-3 static bleeder is meant for ladder line.
THESE DEVICES ARE NOT FOR LIGHTNING PROTECTION AND PROVIDES NO PROTECTION FOR LIGHTNING STRIKES!!!!!
Use for 1″ Cable – RG218, etc.
For 1” cables use five split beads for 80-10 meters (3-30 MHz) or ten split beads for 160-10 (1.8-30 MHz) meters or use 15 for even higher choking for 1-10 MHz. For 144 MHz use only 4 beads as they will provide > 500 ohms. Typical common mode suppression is -9 to 30 dB depending upon the number of beads and frequency. Quite often 20 dB is considered the minimum effective reduction.
Typical Impedance per split bead: 10 MHz: 90 ohms, 25 MHz: 156 ohms, 100 MHz: 250 ohms, 250 MHz: 305 ohms
A minimum impedance of 500 ohms is needed for 50 ohm cable or 10 times the cable impedance for other cables to make a measurable difference in common mode current suppression.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
Note: Ferrite beads may be hexagonal or square shape depending on inventory on hand at time of order.