RF Toroid Calculator by VK3CPU
1:1 Current BalunProduct DetailsModel BA-1-1000 is a 1:1 balun kit used to translate a 50 ohm
unbalanced input to 50 ohms unbalanced at power levels up to 1000 watts
PEP/100 watts continuous when used with a matched load. With a matched
load the SWR will not exceed 1.5 over the frequency range 1.8 to 61 MHz.
1,000 PEP watt rating on a 25% duty cycle. Will sustain about 100 watts RTTY or FT8 at 6 meters. (for higher power use the BA-1-1500 with 6-8 turns for higher frequencies).
Common mode impedance peaks
around 3,500 ohms at 10Mmhz.
With a matched 50 ohm load the SWR over the frequency range 1.8 to 61
MHz is shown in the following table measured with an AIM 4170 network
analyzer. Notice that the conversion from 50 to 50 ohms is very
consistent from 1.8-61 MHz and SWR is less than 1.3:1 over the range
allowing easy tuning by most radio internal antenna tuners or an
external tuner.
Ba-1-1000 1:1 Balun/Unun 1KW PEP 1-61 Mhz
The kit consists of a F140 ferrite toroidal core, enamel insulated
wire, a SO-239 connector with stainless steel hardware, and an
illustrated instruction manual with directions to connect the kit as a 1
to 1 balun/unun (unbalanced coax to unbalanced antenna or balanced
antenna like a dipole). Balun assembly time takes about an hour and is a
fun learning process.
Add a SO-239 Kit on output side to create a 1:1 unun (coax to coax line isolator) or add studs for a balun for use with dipole or beam antenna.
Use the recommwnded CB-Box-1 for a convenient enclosure.
Tutorials
Model BA-1-1000 is a 1:1 balun kit used to translate a 50 ohm
unbalanced input to 50 ohms unbalanced at power levels up to 1000 watts
PEP/100 watts continuous when used with a matched load. With a matched
load the SWR will not exceed 1.5 over the frequency range 1.8 to 61 MHz.
1,000 PEP watt rating on a 25% duty cycle. Will sustain about 100 watts RTTY or FT8 at 6 meters. (for higher power use the BA-1-1500 with 6-8 turns for higher frequencies).
Common mode impedance peaks
around 3,500 ohms at 10Mmhz.
With a matched 50 ohm load the SWR over the frequency range 1.8 to 61
MHz is shown in the following table measured with an AIM 4170 network
analyzer. Notice that the conversion from 50 to 50 ohms is very
consistent from 1.8-61 MHz and SWR is less than 1.3:1 over the range
allowing easy tuning by most radio internal antenna tuners or an
external tuner.
Ba-1-1000 1:1 Balun/Unun 1KW PEP 1-61 Mhz
The kit consists of a F140 ferrite toroidal core, enamel insulated
wire, a SO-239 connector with stainless steel hardware, and an
illustrated instruction manual with directions to connect the kit as a 1
to 1 balun/unun (unbalanced coax to unbalanced antenna or balanced
antenna like a dipole). Balun assembly time takes about an hour and is a
fun learning process.
Add a SO-239 Kit on output side to create a 1:1 unun (coax to coax line isolator) or add studs for a balun for use with dipole or beam antenna.
Use the recommwnded CB-Box-1 for a convenient enclosure.
