CUBE Impedance Transformers (<1:1, 1:1, >1:1)

Store/Antenna Products/CUBE Impedance Transformers (<1:1, 1:1, >1:1)

Palomar Engineers offers a variety of impedance transformers configured as Baluns (balanced coax to unbalanced load) or Ununs (unbalanced coax to unbalanced load) for matching typical 50 ohm feed line impedances to antenna or other load impedances.

We specify impedance ratios as an output to input ratio where the output (or load) is given first and the input is given second (e.g. 100:50 (2:1) would mean a 100 ohm output and a 50 ohm input; a 25:50 (1:2) would mean a 25 ohm load and a 50 ohm input). Most all products use a 50 ohm input unless otherwise specified.

We have products that are available as kits for the do-it-yourself (DIY) person or fully assembled and tested units for the “Plug & Play” crowd.

Note: we use stainless steel eye bolts and studs for all of our balun products. Most balun/unun boxes are 4" x 4" x 2" with some 5KW Hybrids are 4" x4" x 4" size.

50:50 ohm (1:1) Transformers

50:75 ohm (1.5:1) Transformers

50:100 ohm (2:1) Transformers

50:112 ohm (2.25:1) Transformer

50:200 ohm (4:1) Transformers

50:250 ohm (5:1) Transformers

50:300 ohm (6:1) Transformers

50:400 ohm (8:1) Transformers

50:450 ohm (9:1) Transformers

50:600 ohm (12:1) Transformers

50:800 ohm (16:1) Transformers

25:1-81:1 Baluns/Ununs

Multi-Ratio Transformers

Hybrid (NN:1 + 1:1) Transformers

Off Center Fed Dipole Transformers

Ladder Line to coax transformers

Enclosure Boxes and Hardware

Balun/Unun DIY Kits

Wall Wart switching DC power supplies that plug into the AC power line plug and provide DC power to laptops, routers, battery chargers, cell phone chargers, etc are a known source of broadband RFI (a.k.a dirty electricity) that effects many electrical devices including computers, radio receivers, HDTV systems, etc. In many cases this extra RFI noise effects computer I/O speeds since they have to error correct the information packets many more times due to the noise interference causing packet errors. A ferrite ring can often increase data throughput by reducing the error correction to normal rates.

A simple ferrite ring filter on the DC power line can help suppress the RFI noise affecting the victim device or keep the DC power cord from acting as an antenna and radiating RFI into other victim devices. This kit is also useful on laptop computer supplies, routers, cable modems, wireless phone charges, etc.

RFI WW Installation 300x288 - Wall Wart RFI Noise Filter

Installation is quick and easy: Just wrap the DC power cord through the center of the ring filter as many times as you can and reinstall. For best results with long DC power lines, use one at the ring filter at the wall wart end (to prevent the wall wart power supply from using the DC line as an antenna) and another at the DC plug end (to prevent the electronics in the powered device from using the DC power cord as an antenna). Typical installation is shown below:

The filter suppresses RFI in from .1-100 MHz. Inside diameter is 3/4 inch/19 mm.

Since most households and office environments have multiple wall warts we offer the Wall Wart RFI Filter kit in bulk quantity packages.

Known RFI Generators include Roku/Sling-TV power adapter - Interference heard in the AM broadcast band
 and harmonics.
Also many ethernet Cable/DSL modems, cell phone chargers, computer power adapters have the same issue:
using the AC or DC side of the power supply as a radiating antenna.

RFI solution is to use a linear power supply, change adapters or wall wart ferrite filters