Slip On Coax Feed Line Choke - 1"/25.4mm cable, 1.8-300 MHzProduct DetailsBrand: Palomar EngineersMPN: BA-200Country/Region of Manufacture: USAEffective Frequency Range (MHz): 3-61 (5 bead), 1.8-61 (10, 15 bead)PEP Power Rating (watts): same as coax cable ratingChoking Impedance Range (ohms): 5 bead: 200-900, 10 bead: 400-1400, 15 bead: 600-1700Common Mode Attenuation (db): 5 bead: 9-20 db, 10 bead: 16-24 db, 15 bead: 17-25 dbEstimated Insertion Loss (db): .025Input Connector Type: noneOutput Connector Connector Type: noneGround Connector (Y/N): noneEnclosure Size (LxWxH inches): none1″/25.4mm max Cable Size Chokes
Model BA-200. For use with RG-218 and similar size cables up to 1" OD without connectors installed. Works on all impedance cables, 1.8-300 MHz. Choke outside diameter is 2 inches Requires 9-1/2 inches of cable for 5 bead version, 17" of cable for 10 bead version, and 25" of cable for 15 bead version. Use BA-200-10 or BA-200S-15 for higher choking below 21 MHz. For 10-12 meter frequency use 5 beads up to 15 KW PEP, 10 beads for up to 30 KW PEP and 15 beads for up to 45 KW PEP. We use mix 31 for all chokes. Heat shrink weather proofing kit included. Picture shows 10 bead version.
Rule of thumb suggests you need minimum 5x-10x the coax line impedance for effective choking and the more the better as it will reduce common mode current with higher choking impedance. Select chokes with minimum of 500 ohms at your frequency of interest for best results or upgrade to our CUBE(TM), TUBE(TM), Super Choker(TM) chokes up to 15,000 ohms choking.
Select 10 bead version for 160 meter use, 15 bead version for even higher choking power on lower frequencies. Power rating is same as coax cable used power rating.
Typical choking impedances (BA-58, BA-8, BA-200):
1″/25.4mm max Cable Size Chokes
Model BA-200. For use with RG-218 and similar size cables up to 1" OD without connectors installed. Works on all impedance cables, 1.8-300 MHz. Choke outside diameter is 2 inches Requires 9-1/2 inches of cable for 5 bead version, 17" of cable for 10 bead version, and 25" of cable for 15 bead version. Use BA-200-10 or BA-200S-15 for higher choking below 21 MHz. For 10-12 meter frequency use 5 beads up to 15 KW PEP, 10 beads for up to 30 KW PEP and 15 beads for up to 45 KW PEP. We use mix 31 for all chokes. Heat shrink weather proofing kit included. Picture shows 10 bead version.
Rule of thumb suggests you need minimum 5x-10x the coax line impedance for effective choking and the more the better as it will reduce common mode current with higher choking impedance. Select chokes with minimum of 500 ohms at your frequency of interest for best results or upgrade to our CUBE(TM), TUBE(TM), Super Choker(TM) chokes up to 15,000 ohms choking.
Select 10 bead version for 160 meter use, 15 bead version for even higher choking power on lower frequencies. Power rating is same as coax cable used power rating.
Typical choking impedances (BA-58, BA-8, BA-200):
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.