Multi Ratio 4:1/6:1/9:1 CUBE™ Balun, 1.8-61 MHz, 1.5 KWProduct DetailsMPN: CB-4-9-1500Country/Region of Manufacture: USAType: Balanced output (BALUN)Input ohms/Output ohms: 50:200, 50:450Frequency Range < 2:1 SWR (MHz): 1.8-61 MHzPEP Power Rating (watts): 1500
1500 Watt 4:1/6:1/9:1 CUBE™ Balun – Model CB-4-9-1500
Model CB-4-9-1500 is a 4:1 and a 9:1 balanced output (balun) housed in a Nema enclosure box (4″ x 4″ x 2″) with a top eyebolt halyard hoist, two side studs for 4:1 and two additional side studs for 9:1 outputs, each capable of input power levels up to 1.5 KW PEP when used with a matched load. The 4:1 ratio takes 50 ohms input and matches to 200 ohms output and the 9:1 ratio takes 50 ohm input and matches to 450 ohms output between 1-61 MHz under 2:1 SWR under matched load conditions.
Now you don’t need to buy two separate baluns or guess which balun to use - you get the 4:1 and the the 9:1 in a single package! – just buy the CB-4-9-1500 and pick the output ratio that best matches your antenna tuner! (Note: you can only use 1 set of outputs at a time)
Application note: If you use 1 of the 4:1 and 1 of the 9:1 terminals on opposite sides, then the output wlll be 300 ohms or a 6:1 balun!
1500 Watt 4:1/6:1/9:1 CUBE™ Balun – Model CB-4-9-1500
Model CB-4-9-1500 is a 4:1 and a 9:1 balanced output (balun) housed in a Nema enclosure box (4″ x 4″ x 2″) with a top eyebolt halyard hoist, two side studs for 4:1 and two additional side studs for 9:1 outputs, each capable of input power levels up to 1.5 KW PEP when used with a matched load. The 4:1 ratio takes 50 ohms input and matches to 200 ohms output and the 9:1 ratio takes 50 ohm input and matches to 450 ohms output between 1-61 MHz under 2:1 SWR under matched load conditions.
Now you don’t need to buy two separate baluns or guess which balun to use - you get the 4:1 and the the 9:1 in a single package! – just buy the CB-4-9-1500 and pick the output ratio that best matches your antenna tuner! (Note: you can only use 1 set of outputs at a time)
Application note: If you use 1 of the 4:1 and 1 of the 9:1 terminals on opposite sides, then the output wlll be 300 ohms or a 6:1 balun!
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.