ICOM M700, M710 Marine Radio RFI and Noise Reduction Kit, RFI Range 1-60 MHz, NO RADIOProduct DetailsMPN: RFI-HF-BASEType: NEWCountry/Region of Manufacture: United StatesFilter Power Rating (PEP watts): 500RFI Suppression Range (MHz): 1-300 MHz# Ferrite Filters: 5Enclosure Size (inches): n/aTypical Use:: AC/DC power, RF output, 3 additional I/O linesPalomar Engineers RFI Filter Kit for ICOM M700PRO and M710 HF Transceivers - RFI Kit ONLY - NO RADIO INCLUDED
BUY THIS KIT NOW TO REDUCE NOISE IN THE RECEIVER AND SUPPRESS INTERFERENCE TO/FROM OTHER ELECTRONICS ON YOUR VESSEL.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable and antenna tuner cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to other electronic devices including audio/video systems, computers, marine electronics, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and antenna tuner s used on marine systems. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
Included are the following chokes and installation guidelines:
MC-1-1500-50 RF Input/Output: Coax Common Mode Noise filter installed between radio and antenna tuner coax to reduce noise into receiver and suppress RFI.
double male barrel connector on each end for joining noise filter directly to antenna tuner.
DC Input Filter: F240, 1.4" ID – coil 3-7 turns of DC power cable through center
Antenna Tuner Cable Filters: 2 clamp on filters - 1/2 snap on for 1-2 turns through center at each end of cable.
NOTE: RADIO NOT INCLUDED!
On Sale
Home Theater System RFI Kit for AC Powered Sub-Woofers Only - 5 filtersHome Theater System RFI Kit for AC Powered Sub-Woofers Only - 5 filtersSKU RFI-HTS-SWList price $35.80 Save 16%$29.95On Sale
DC Voltage Common Mode Noise Filter - Marine, RV, Communications, 600 Volts/30 AmpsDC Voltage Common Mode Noise Filter - Marine, RV, Communications, 600 Volts/30 AmpsSKU RFI-DC-30List price $109.95 Save 18%$89.95
Palomar Engineers RFI Filter Kit for ICOM M700PRO and M710 HF Transceivers - RFI Kit ONLY - NO RADIO INCLUDED
BUY THIS KIT NOW TO REDUCE NOISE IN THE RECEIVER AND SUPPRESS INTERFERENCE TO/FROM OTHER ELECTRONICS ON YOUR VESSEL.
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable and antenna tuner cable.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to other electronic devices including audio/video systems, computers, marine electronics, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and antenna tuner s used on marine systems. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
Included are the following chokes and installation guidelines:
MC-1-1500-50 RF Input/Output: Coax Common Mode Noise filter installed between radio and antenna tuner coax to reduce noise into receiver and suppress RFI.
double male barrel connector on each end for joining noise filter directly to antenna tuner.
DC Input Filter: F240, 1.4" ID – coil 3-7 turns of DC power cable through center
Antenna Tuner Cable Filters: 2 clamp on filters - 1/2 snap on for 1-2 turns through center at each end of cable.
NOTE: RADIO NOT INCLUDED!
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.