Bullet Hybrid (16:1) HF Balun + 1:1 Choke, 1.8-31 MHz, 500 Watts, T2FD, BBTD, ALEProduct DetailsCountry/Region of Manufacture: USAType: NEWInput ohms/Output ohms: 50 in, 800 outFrequency Range < 2:1 SWR (MHz): 1.8-30PEP Power Rating (watts): 500Transformer Topology: Broadband FerriteHardware Type: Stainless SteelWeight (pounds): 2Antenna Compatability: T2FD, BBTD, ALE, RhombicThe Bullet-16-1-500EB is a multi-core, 16:1 balun plus a 1:1 feed line choke in a single compact (looks like a bullet) enclosure that is lightweight and easy to transport for your fixed/portable ALE, T2FD or BBTD antenna systems. Also useful for rhombics and other wire antennas needing balanced 450 ohm output. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output.Use a 800 ohm non-inductive termination resistor (Our part# TR-800-600) for the T2FD when using this balun. Note you may also use a 1000 ohm resistor with similar results (Part# TR-1000-600)
Need higher power capability? See our 1500 watts 16:1 hybrid (part# CB-16-1-1500)
Remember we over engineer our products, to out perform our competition - just compare the weight and frequency range of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
On Sale
Termination Resistor, 500 Ohm Non-Inductive for T2FD, BBTD, Rhombic, 1-61 MHz, 600 WattsTermination Resistor, 500 Ohm Non-Inductive for T2FD, BBTD, Rhombic, 1-61 MHz, 600 WattsSKU TR-500-600List price $129.95 Save 23%$99.95
The Bullet-16-1-500EB is a multi-core, 16:1 balun plus a 1:1 feed line choke in a single compact (looks like a bullet) enclosure that is lightweight and easy to transport for your fixed/portable ALE, T2FD or BBTD antenna systems. Also useful for rhombics and other wire antennas needing balanced 450 ohm output. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output.Use a 800 ohm non-inductive termination resistor (Our part# TR-800-600) for the T2FD when using this balun. Note you may also use a 1000 ohm resistor with similar results (Part# TR-1000-600)
Need higher power capability? See our 1500 watts 16:1 hybrid (part# CB-16-1-1500)
Remember we over engineer our products, to out perform our competition - just compare the weight and frequency range of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.