50:600 ohm, (12:1) CUBE™ Balun/Unun, 1.8-31 MHz Balun/Unun, RX Only/1KW/2KW/3KW PEP, T2FD, Rhombic, End Fed, FlagpoleProduct DetailsCountry/Region of Manufacture: United StatesType: NewInput ohms/Output ohms: 50 in/600 out balanced (balun) or unbalunced (unun)Frequency Range < 2:1 SWR (MHz): 1.8-31PEP Power Rating (watts): RX only/1000/2000/3000Insertion Loss (dB): < .1 dBInput Connector: SO-239Hardware Type: Stainless SteelEnclosure Size: 4 x 4 x 2, 3KW = 4 X 4 x 4Weight (pounds): 2
HF 12:1 Impedance Transformers
12:1 Baluns are useful transformers for 600 ohm balanced loads the impedance at the end of the feed line is 600 ohms (1/2 wavelength feed line), or high impedance feeds for rhombic, T2FD and traveling wave antennas.
12:1 Ununs are useful between coax and long wires with a load impedance near 600 ohms like a beverage antenna. Shortwave listener antennas also can benefit with the 12:1 unun and it may provide a better match than 9:1 ununs – this means quieter noise levels and stronger signals so you can hear distance stations easier.
For end fed antennas, use a 9:1 unun or 12:1 unun - also available in the "Bullet" antenna end fed style (Bullet-12U-500)
Receive only baluns/ununs are rated for 100 watts PEP
All enclosure boxes have 2 side flanges with 1/4" holes.
All of these products are made to order and typical production time is 10 days depending on quantity.
HF 12:1 Impedance Transformers
12:1 Baluns are useful transformers for 600 ohm balanced loads the impedance at the end of the feed line is 600 ohms (1/2 wavelength feed line), or high impedance feeds for rhombic, T2FD and traveling wave antennas.
12:1 Ununs are useful between coax and long wires with a load impedance near 600 ohms like a beverage antenna. Shortwave listener antennas also can benefit with the 12:1 unun and it may provide a better match than 9:1 ununs – this means quieter noise levels and stronger signals so you can hear distance stations easier.
For end fed antennas, use a 9:1 unun or 12:1 unun - also available in the "Bullet" antenna end fed style (Bullet-12U-500)
Receive only baluns/ununs are rated for 100 watts PEP
All enclosure boxes have 2 side flanges with 1/4" holes.
All of these products are made to order and typical production time is 10 days depending on quantity.
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.