50:450 ohm (9:1) CUBE™ Balun, 1.8-31 MHz, 5 KW, ladder line, ZEPP, T2FDProduct DetailsMPN: CB-9-5000Input ohms/Output ohms: 50 in / 450 outputFrequency Range < 2:1 SWR (MHz): 1-31PEP Power Rating (watts): 5000Model CB-9-5000 is a 9:1 multi-core, balanced output balun housed in a NEMA enclosure box (4″ x 4″ x 2″) with top studs (TS) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 5000 watts PEP when used with a matched load. With matched 450 ohm load the SWR over the frequency range 1 to 31 MHz is less than 2:1 on the coax feed side.
All power rating are PEP, 100%, continuous digital modes are 30% duty factor rating of PEP, FT-8 digital mode rated at 1500 watts.
Application note: If using 450 ohm ladder line on the output of the balun top studs, make sure the impedance seen at the balun end of the ladder line is near 450 ohms since the ladder line acts as an impedance transformer, the impedance at the end of the ladder line may be different than the characteristic 450 ohms of the ladder line. For example a 1/4 wavelength of ladder line will transform a high impedance at the antenna feed point to a very low impedance at the other end connected to the balun thus placing a very low impedance load on a balun expecting 450 ohms and such a load may damage the balun. The impedance seen at the balun output should be near 450 ohms for full power rating.
Model CB-9-5000 is a 9:1 multi-core, balanced output balun housed in a NEMA enclosure box (4″ x 4″ x 2″) with top studs (TS) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 5000 watts PEP when used with a matched load. With matched 450 ohm load the SWR over the frequency range 1 to 31 MHz is less than 2:1 on the coax feed side.
All power rating are PEP, 100%, continuous digital modes are 30% duty factor rating of PEP, FT-8 digital mode rated at 1500 watts.
Application note: If using 450 ohm ladder line on the output of the balun top studs, make sure the impedance seen at the balun end of the ladder line is near 450 ohms since the ladder line acts as an impedance transformer, the impedance at the end of the ladder line may be different than the characteristic 450 ohms of the ladder line. For example a 1/4 wavelength of ladder line will transform a high impedance at the antenna feed point to a very low impedance at the other end connected to the balun thus placing a very low impedance load on a balun expecting 450 ohms and such a load may damage the balun. The impedance seen at the balun output should be near 450 ohms for full power rating.
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.