50:50 ohm (1:1) Common Mode Choke HF Balun Kit - 1500 watt PEP, 1.8-31 MHzProduct DetailsInput ohms/Output ohms: 50 in, 50 outFrequency Range < 2:1 SWR (MHz): 1.8-30PEP Power Rating (watts): 1500Model BA-1-1500 is a 1:1 balun kit used to translate a 50 ohm unbalanced input to 50 ohms unbalanced at power levels up to 1500 watts PEP when used with a matched load. With a matched load the SWR will not exceed 1.5 over the frequency range 1.8 to 30 MHz. 1,500 PEP watt rating on a 25% duty cycle.
The kit consists of a F240 ferrite core, two colors of selected insulated wire, two SO-239 connectors (one for input and one for output connections) with stainless steel hardware, and an illustrated instruction manual with directions to assemble the kit as a 1 to 1 balun (unbalanced coax to balanced antenna/load) or unun (unbalanced to unbalanced). Leave one of the SO-239 connectors off on the output side and connect to your balanced antenna (dipole, beam driven elements, etc). To use as a line isolator/common mode choke, use both SO-239 connectors and insert in series with the coax feed line. For best results use one at the antenna and one for the rig side at the antenna tuner. The number of turns on the toroid can be changed to emphasize the low, mid or high portion of the 160-10 meter bands range as well as the choking impedance (see graph below). Assembly time is about 30 minutes. You can vary the number of turns to emphasize different frequency ranges.
BA-1-1500 Choking Z magnitude – 14 Turns and 10 Turns
Just add your custom enclosure, or optional enclosure box below, with the kit and you have a compete 1:1 current balun/unun.
Model BA-1-1500 is a 1:1 balun kit used to translate a 50 ohm unbalanced input to 50 ohms unbalanced at power levels up to 1500 watts PEP when used with a matched load. With a matched load the SWR will not exceed 1.5 over the frequency range 1.8 to 30 MHz. 1,500 PEP watt rating on a 25% duty cycle.
The kit consists of a F240 ferrite core, two colors of selected insulated wire, two SO-239 connectors (one for input and one for output connections) with stainless steel hardware, and an illustrated instruction manual with directions to assemble the kit as a 1 to 1 balun (unbalanced coax to balanced antenna/load) or unun (unbalanced to unbalanced). Leave one of the SO-239 connectors off on the output side and connect to your balanced antenna (dipole, beam driven elements, etc). To use as a line isolator/common mode choke, use both SO-239 connectors and insert in series with the coax feed line. For best results use one at the antenna and one for the rig side at the antenna tuner. The number of turns on the toroid can be changed to emphasize the low, mid or high portion of the 160-10 meter bands range as well as the choking impedance (see graph below). Assembly time is about 30 minutes. You can vary the number of turns to emphasize different frequency ranges.
BA-1-1500 Choking Z magnitude – 14 Turns and 10 Turns
Just add your custom enclosure, or optional enclosure box below, with the kit and you have a compete 1:1 current balun/unun.
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer