50:450 ohm (9:1) CUBE™ Balun, 1.8-61 MHz, 1.5 KW, SO-239 UHF Input, BBTD, Traveling Wave AntennasProduct DetailsMPN: CB-9-1500TS (top studs), CB-9-1500EB (eyebolts)Country/Region of Manufacture: USAInput ohms/Output ohms: 50 in / 450 outputFrequency Range < 2:1 SWR (MHz): 1.8-61PEP Power Rating (watts): 1500Input Connector: SO-239Output Connector(s): Top Studs/Side EyeboltsHardware Type: Stainless SteelEnclosure Size: 4" x 4" x 2"Weight (pounds): 3Antenna Compatability: Folded Dipole, T2FD, BBTD, ALEModel CB-9-1500 is a 9:1 multi-core, balanced output balun housed in a water resistant enclosure with top stud/wingnuts (TS) or Eye bolts (halyard top hoist, side eye bolts/outputs) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 1500 watts PEP when used with a matched load. With matched 450 ohm load the SWR over the frequency range 1.8 to 61 MHz is less than 2:1 on the coax feed side. Actual SWR is under 1.25:1 from 1.8-180 MHz so very useful for 30-150 MHz also - see graphs for specific details
Features
* Wide Frequency Range 1.8-161 MHz, usable to 180 MHz < 1.25:1 into resistive load
* High Power, 1500 watts PEP (up to 61 MHz)
* Convenient side tab mounting feet
Many designs for BBTD antennas using 9:1 baluns at HFLINK.COM
We also have the 9:1 with the built-in 1:1 choke/balun in part# CB-9-1-1500EB
Model CB-9-1500 is a 9:1 multi-core, balanced output balun housed in a water resistant enclosure with top stud/wingnuts (TS) or Eye bolts (halyard top hoist, side eye bolts/outputs) used to translate a 50 ohm input up to 450 ohms at RF power levels up to 1500 watts PEP when used with a matched load. With matched 450 ohm load the SWR over the frequency range 1.8 to 61 MHz is less than 2:1 on the coax feed side. Actual SWR is under 1.25:1 from 1.8-180 MHz so very useful for 30-150 MHz also - see graphs for specific details
Features
* Wide Frequency Range 1.8-161 MHz, usable to 180 MHz < 1.25:1 into resistive load
* High Power, 1500 watts PEP (up to 61 MHz)
* Convenient side tab mounting feet
Many designs for BBTD antennas using 9:1 baluns at HFLINK.COM
We also have the 9:1 with the built-in 1:1 choke/balun in part# CB-9-1-1500EB
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer