ICOM M700, M710 Marine Radio RFI and Noise Reduction Kit, RFI Range 1-60 MHz, NO RADIO

Name: ICOM M700, M710 Marine Radio RFI and Noise Reduction Kit, RFI Range 1-60 Mz
Brand: Palomar Engineers
SKU: RFI-ICOM-M700/710
Price: 89.95 USD
Availability: InStock

Store/RFI Solution Kits/Radio Communication RFI Solutions/HF/VHF Transceiver RFI/Noise Kits/Icom Transceiver RFI Kits

SKU RFI-ICOM-M700/710

$89.95

Bulk pricing available for quantities of 2 units or more

Quantity:

Buy more, save more

Quantity	Price per item	Discount
2 items	$81.95	9% off

Save this product for later

Customer reviews

No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in

ICOM M700, M710 Marine Radio RFI and Noise Reduction Kit, RFI Range 1-60 MHz, NO RADIO

Store/RFI Solution Kits/Radio Communication RFI Solutions/HF/VHF Transceiver RFI/Noise Kits/Icom Transceiver RFI Kits

Product Details

MPN: RFI-HF-BASE

Type: NEW

Country/Region of Manufacture: United States

Filter Power Rating (PEP watts): 500

RFI Suppression Range (MHz): 1-300 MHz

# Ferrite Filters: 5

Enclosure Size (inches): n/a

Typical Use:: AC/DC power, RF output, 3 additional I/O lines

Palomar Engineers RFI Filter Kit for ICOM M700PRO and M710 HF Transceivers - RFI Kit ONLY - NO RADIO INCLUDED

BUY THIS KIT NOW TO REDUCE NOISE IN THE RECEIVER AND SUPPRESS INTERFERENCE TO/FROM OTHER ELECTRONICS ON YOUR VESSEL.

Purpose

The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable and antenna tuner cable.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to other electronic devices including audio/video systems, computers, marine electronics, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and antenna tuner s used on marine systems. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

Included are the following chokes and installation guidelines:

MC-1-1500-50 RF Input/Output: Coax Common Mode Noise filter installed between radio and antenna tuner coax to reduce noise into receiver and suppress RFI.

double male barrel connector on each end for joining noise filter directly to antenna tuner.

DC Input Filter: F240, 1.4" ID – coil 3-7 turns of DC power cable through center

Antenna Tuner Cable Filters: 2 clamp on filters - 1/2 snap on for 1-2 turns through center at each end of cable.

NOTE: RADIO NOT INCLUDED!

Mobile RFI kits work two ways: They suppress RFI from on board computers and other sensing/control devices in your vehicle that may cause your radio to be a VICTIM of RFI, and second they suppress RFI generated by your radio as a SOURCE which may affect your on board computers or other devices. Mobile operations of HF radios (1-30 Mhz) tend to experience more RFI effects than VHF/UHF mobile stations. If you have both HF and VHF installations in your vehicles, you may need both kits.

To address separate solutions we have developed two separate RFI kits: one for HF (1.8-300 MHz) mobile installations and another for VHF/UHF (30-1000 MHz) mobile installations. Each kit uses the appropriate ferrite mix for the frequency range desired.