Mobile Station RFI Kits

Bullet 50:200 (4:1) HF Balun, 1.8-61 MHz, 500/1500 Watts PEP, Loop, OCF, ZEPP

SKU Bullet-4B-500EB
$89.95
Bulk pricing available for quantities of 2 units or more
PEP Power Rating
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$79.9511% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
Bullet 50:200 (4:1) HF Balun, 1.8-61 MHz, 500/1500 Watts PEP, Loop, OCF, ZEPP
Product Details
Country/Region of Manufacture: USA
Type: NEW
Input ohms/Output ohms: 50 in, 200 out
Frequency Range < 2:1 SWR (MHz): 1.8-61
PEP Power Rating (watts): 500/1500
Input Connector: UHF SO-239
Output Connector(s): Eyebolt/Wingnut
Transformer Topology: Broadband
Hardware Type: Stainless - 1/4"
Antenna Compatability: OCF, Zepp, Folded Dipole, Loop

The Bullet-4B-500 and SBullet-4B-1500 are multi-core core baluns with a compact enclosure (looks like a bullet) enclosure that is physically lightweight but electrically robust and easy to transport for your portable loop antenna solution or permanent installation. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Choose your model rated 500 or 1500 Watts PEP from 1.8-61 MHz.

This transformer requires a feed line choke (see related products) to isolate the coax feed line from the antenna. A coax noise filter at the radio end of the coax is also recommended for best results.

Vertical Delta Loops

Multi-band vertical delta loops can be oriented several way but the most popular is to have the “pointy” end at the top (usually a single support) and the lower horizontal ends just out of reach of humans and animals. Best feed point at the top for multi-band use with a 4;1 balun. CUt total wire length to 1005/F (MHz) where F is lowest band frequency of use..

Single band vertical delta loops are best fed 1/4 wavelength (246/f(MHz)) from the top point down one side. Vertical delta loops use the same 2:1 baluns as the horizontal loops.

NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.

Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.


Mobile RFI kits work two ways: They suppress RFI from on board computers and other sensing/control devices in your vehicle that may cause your radio to be a VICTIM of RFI, and second they suppress RFI generated by your radio as a SOURCE which may affect your on board computers or other devices.  Mobile operations of HF radios (1-30 Mhz) tend to experience more RFI effects than VHF/UHF mobile stations.  If you have both HF and VHF installations in your vehicles, you may need both kits.

To address separate solutions we have developed two separate RFI kits: one for HF (1.8-300 MHz) mobile installations and another for VHF/UHF (30-1000 MHz) mobile installations.  Each kit uses the appropriate ferrite mix for the frequency range desired.