5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
Snap On RF Choke/Isolator - 1/4"/6mm cable, RG-58/59/06/LMR240 - 3-300 MHz, -5/10/15 Bead OptionProduct DetailsBrand: Palomar EngineersMPN: SNO-1/4-5Effective Frequency Range (MHz): 3-300PEP Power Rating (watts): same as coax cable ratingChoking Impedance Range (ohms): 5 bead: 500-1000, 10 bead: 600-1800, 15 bead: 1000-2100Common Mode Attenuation (db): 5 bead: 16-22db, 10 bead: 17-25db, 15 bead: 21-27 dbEstimated Insertion Loss (db): .025Input Connector Type: noneOutput Connector Connector Type: noneGround Connector (Y/N): noneEnclosure Size (LxWxH inches): noneUse for 1/4″ Cable – RG-58, RG59, RG-6, LMR-240, etc
For 1/4” cables use five FSB31-1/4 split beads for 80-10 meters (3-30 mHz) or ten FSB31-1/4 split beads for 160-10 (1.8-30 MHz) meters or use 15 FSB31-1/4 for even higher choking for 1-10 MHz.
Typical Impedance per split bead: 10 MHz: 100 ohms, 25 MHz: 163 ohms, 100 MHz: 275 ohms, 250 MHz: 275 ohm
Select 10 bead version for 160 meter use. Minimum recommended total impedance is 500 ohms at frequency of interest.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
Use for 1/4″ Cable – RG-58, RG59, RG-6, LMR-240, etc
For 1/4” cables use five FSB31-1/4 split beads for 80-10 meters (3-30 mHz) or ten FSB31-1/4 split beads for 160-10 (1.8-30 MHz) meters or use 15 FSB31-1/4 for even higher choking for 1-10 MHz.
Typical Impedance per split bead: 10 MHz: 100 ohms, 25 MHz: 163 ohms, 100 MHz: 275 ohms, 250 MHz: 275 ohm
Select 10 bead version for 160 meter use. Minimum recommended total impedance is 500 ohms at frequency of interest.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
