5:1 CUBE™ Unun – Model CU-5-1500 (50:250 Ohm, 1.8-61 MHz, 1.5KW PEP)
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 unun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical application:
Also available as a balanced output – CB-5-1500
Coax Common Mode Noise Filter
Common mode current induced by radiated sources (plasma TV, routers, computers, transmitters, etc) can be picked up by the outside of the coax braid from the antenna feed point back to the receiver. This portion of the coax braid acts like a receiving antenna, picking up common mode noise signals that override weak signals making them difficult or impossible to hear!
The solution? A common mode noise filter with high choking impedance at the receiver end of the coax.
Do you have common mode noise on your coax? Here is a simple test (pdf)
1. Remove the coax connector and measure the noise level.
2. Now insert the coax connector CENTER CONDUCTOR ONLY into the SO-239 antenna input and measure
the noise level (it should be higher and include possible signals)
3. Now connect the OUTER SHELL of the coax connector to the antenna input and measure the noise
level. If it is higher you have common mode noise and the common mode noise filter will help suppress this noise which
is carried on the outside of the coax braid (acting as a second receive antenna).
Common mode noise suppression with the Palomar CMNF series of filters is typically 25-36 dB which is equivalent to 4-6 “S” units on radios with 6 dB/”S” unit or may be more on radios with 3dB/”S” unit.
Note for antenna switch users, perform the above test on each antenna coax lead separately to determine if that particular antenna braid is contributing noise to the receiver – use a coax noise filter on the antennas that have common mode noise.
Refine by 
MINI-BALUN 1:1 Coax Interface to Ladder Line, Dipole elements, 500 Watts PEP, up to -38Db Common Mode Rejection, 1-61 MHz, Flagpole, Dipole, Beam and G5RV/ZS6BKW AntennasMINI-BALUN 1:1 Coax Interface to Ladder Line, Dipole elements, 500 Watts PEP, up to -38Db Common Mode Rejection, 1-61 MHz, Flagpole, Dipole, Beam and G5RV/ZS6BKW AntennasSKU MB-1-500SS$69.95
RFI Common Mode Noise Filter Kits for Generic Antenna Switches - Isolate Non-Selected Coax Braid Noise!RFI Common Mode Noise Filter Kits for Generic Antenna Switches - Isolate Non-Selected Coax Braid Noise!Suppress Unwanted Noise & RFISKU RFI-AS-GEN-2$129.95
Coax Common Mode Noise Filter
Common mode current induced by radiated sources (plasma TV, routers, computers, transmitters, etc) can be picked up by the outside of the coax braid from the antenna feed point back to the receiver. This portion of the coax braid acts like a receiving antenna, picking up common mode noise signals that override weak signals making them difficult or impossible to hear!
The solution? A common mode noise filter with high choking impedance at the receiver end of the coax.
Do you have common mode noise on your coax? Here is a simple test (pdf)
1. Remove the coax connector and measure the noise level.
2. Now insert the coax connector CENTER CONDUCTOR ONLY into the SO-239 antenna input and measure
the noise level (it should be higher and include possible signals)
3. Now connect the OUTER SHELL of the coax connector to the antenna input and measure the noise
level. If it is higher you have common mode noise and the common mode noise filter will help suppress this noise which
is carried on the outside of the coax braid (acting as a second receive antenna).
Common mode noise suppression with the Palomar CMNF series of filters is typically 25-36 dB which is equivalent to 4-6 “S” units on radios with 6 dB/”S” unit or may be more on radios with 3dB/”S” unit.
Note for antenna switch users, perform the above test on each antenna coax lead separately to determine if that particular antenna braid is contributing noise to the receiver – use a coax noise filter on the antennas that have common mode noise.
