Th CU-1-1500 unun is useful as common mode feed line chokes or coax to antenna interfaces. SO-239 output models can also be used with balanced antennas if a short coax cable “pigtail” is used on the output and connected to the antenna. Rated 1500 Watts PEP from 1.8-61 MHz. Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid. Much more effective then our sleeve feed line chokes due to our exclusive Multimix(TM) multi-core topology using high permeability ferrite cores which provides a high choking impedance over a broad frequency range. Typical common mode suppression is 20-38 dB (up to 6 "S" units) from 1.8-61 MHz reduces common mode current! For most effective results, use 1 choke at the antenna and another at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid. Optionally available with both input and output on same side for certain installations and wall mounts available on each side for both models. Choose SO-239 UHF or N connector input/output connectors
1500 Watt Rated 1:1 CUBE™ Unun
For RFI common mode suppression use, mix 31 is effective from 1-300 Mhz, mix 43 works from 25-300 Mhz, Mix 61 is for 200-2000 Mhz, and mix 77 favors .1-50 MHz. These frequencies are those of the interfering signal to be eliminated, not the operating frequencies of the equipment to be protected. See Mix Selection for other applications.
NOW WITH QUANTITY PRICING FOR CLUB , VOLUME PURCHASERS!
Bead dimensions are shown in the picture below and in the table as A, B, C
Ferrite Bead Dimensions
Application Note: Use impedances for each bead at your desired frequency to select number of beads needed for desired Z. For example if you have a 50 ohm RG-8 coax cable and want a choking impedance of 500 ohms at 10 Mhz, you can check the FB102 column (since FB102 will pass RG-8 through its center ID) at 10Mhz and find that Mix 31 has a Z of 108 ohms/bead and Mix 43 has a Z of 91 ohms/bead. For 500 ohms we would need 5 mix 31 beads or 6 mix 43 beads to have greater than 500 ohms. Mix 31 has better response below 10 Mhz but above 10 Mhz mix 31 and mix 43 are very close. If you need more Z, just use more beads in series on the cable or use more windings thru a larger ID bead (e.g. USE FB102-31 for 4 turns of RG-8X for 16X increase in Z per bead – see pictures below for examples). Use Mix 61 for VHF and above for RFI/EMI suppression and below 30 Mhz for multi-ratio impedance transformers (baluns/ununs). See Mix Selection for other applications.
For extra large cables use the FB400-31 which has an inside diameter of 3 inches (76mm).
Frequency Range Comparison Chart
(FB56-xx size)
Multi-turn Common Mode Choking Impedance Increase Example (FB56-43)
Ferrite Bead relative size comparison
Left to right sizes: FB56 (ID = .25″), FB102 (ID=.505″), FB103 (ID=.77″)
SLIP ON Sizes for Heliax and Coax Cable
Cascaded Common Mode Chokes/Line Isolators/1:1 Baluns
 RG58 4 turns on 2 FB102-31 for 2000 ohms choking impedance |
 RG58 12 turns on FT240-43 for 4000-6000 ohms choking impedance |
Handy Wire Size reference for ferrite bead sizes needed
————————————————–/———————————————————
Connector already on cable? See Snap On Ferrite Beads for convenient installation on cables with connector already installed.