Off Center Fed (OCF) Dipole Baluns

2302699123 - Off Center Fed (OCF) Dipole Baluns
+3

Snap On RF Choke - 1/2"/12.7mm cable -5/10/15 Bead Option, 100 KHz - 5 MHz, Excellent in AM Broadcast Band

SNO75-1/2-5
$64.75
In stock
1
Product Details
Brand: Palomar Engineers
MPN: SNO75-1/2-5, -10, -15
Country/Region of Manufacture: United States
Effective Frequency Range (MHz): 100 KHz - 30 Mhz
PEP Power Rating (watts): same as coax cable rating
Common Mode Attenuation (db): see graph
Estimated Insertion Loss (db): .025

Use for 1/2″ Cable – RG8, RG213, LMR-400, AC/DC and signal cable for suppression of common mode current (RFI) from 100 KHz to 30 MHz

Typical common mode suppression up to 22 dB depending upon the number of beads and frequency. Quite often 20 dB is considered the minimum effective reduction.

A minimum impedance of 500 ohms is needed for 50 ohm cable or 10 times the cable impedance for other cables to make a measurable difference in common mode current suppression.

The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.

As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.

Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.

Tech note: For RFI frequencies over 3.75 MHz, choose SNO31-1/2-5, 10 or 15 for improved common mode rejection (see graph for comparison)

Note: Ferrite beads may be hexagonal or square shape depending on inventory on hand at time of order.
Save this product for later
Display prices in: USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG