Off Center Fed (OCF) Dipole Baluns

930357466 - Off Center Fed (OCF) Dipole Baluns
+3

Multi Ratio 4:1/6:1/9:1 CUBE™ Balun, 1.8-61 MHz, 1.5 KW

CB-4-9-1500
$129.95
In stock
1
Product Details
MPN: CB-4-9-1500
Country/Region of Manufacture: USA
Type: Balanced output (BALUN)
Input ohms/Output ohms: 50:200, 50:450
Frequency Range < 2:1 SWR (MHz): 1.8-61 MHz
PEP Power Rating (watts): 1500


1500 Watt 4:1/6:1/9:1 CUBE™ Balun – Model CB-4-9-1500

Model CB-4-9-1500 is a 4:1 and a 9:1 balanced output (balun) housed in a Nema enclosure box (4″ x 4″ x 2″) with a top eyebolt halyard hoist, two side studs for 4:1 and two additional side studs for 9:1 outputs, each capable of input power levels up to 1.5 KW PEP when used with a matched load. The 4:1 ratio takes 50 ohms input and matches to 200 ohms output and the 9:1 ratio takes 50 ohm input and matches to 450 ohms output between 1-61 MHz under 2:1 SWR under matched load conditions.

Now you don’t need to buy two separate baluns or guess which balun to use - you get the 4:1 and the the 9:1 in a single package! – just buy the CB-4-9-1500 and pick the output ratio that best matches your antenna tuner! (Note: you can only use 1 set of outputs at a time)

Application note: If you use 1 of the 4:1 and 1 of the 9:1 terminals on opposite sides, then the output wlll be 300 ohms or a 6:1 balun!

Save this product for later
Display prices in: USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG