Palomar Engineers RFI Filter Kit for HF Base Radio Mobile Transceivers up to 300 MHz
BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL RADIO RIGS
Purpose
The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable. Additional chokes are included to reduce common mode currents on 3 more transceiver cables including computer control, audio and another.
This kit will help reduce or eliminate:
1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.
2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.
3. RFI to your other radios, audio/video systems, computers, telephones, etc.
A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).
These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.
The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.
Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.
Included are the following chokes and installation guidelines:
RF Input/Output: F240 for toroid balun – 5-9 turns of RG-58/RG-8X size coax cable through center
DC Input: F240 – 3-7 turns of DC power cable
3 additional I/O cables - 1/2 snap on for 1-2 turns through center. Multiple wires can share the same filter.
For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line.If you use a linear amplifier use an amplifier RFI kit for additional RFI interference suppression.
Testimonial
Hi Bob,
Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013
I operate mainly on the digital modes running less than 50 Watts. All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun. They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads. I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.
Here are my findings:
- No more RFI displayed on the monitors.
- Radio not acting up or turning off.
- The SWR at 160/80 meter is 1.2:1
- No antenna tuner required. (radio goes to Bypass automatically.)
- Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
- One happy OCFD user!
Thanks to Palomar Engineers design and engineering for solving this issue.
73, Ernest – W4EG