Off Center Fed (OCF) Dipole Baluns

442300472 - Off Center Fed (OCF) Dipole Baluns
+8
+7
+6
+5
+4
+3
+2

FSB31-1, ID=1", RFI Range 1-300 MHz, Bulk Pack of 3

Store/Ferrite Core Products/Mix 31/Snap On - Mix 31 - RFI Range 1-300 MHz
SKU FSB31-1-3
$49.95
On Sale
List price $58.50 Save 15%
3
$18.32
1
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
Pin it
FSB31-1, ID=1", RFI Range 1-300 MHz, Bulk Pack of 3
Store/Ferrite Core Products/Mix 31/Snap On - Mix 31 - RFI Range 1-300 MHz
Product Details
MPN: FSB31-1
Initial Permeability (@ 10KHz): 1500
Material: MnZn
Max cable size - in/mm: 1.0/25.4
OD (A) - in/mm: 2.22/56.4
ID (B) - in/mm: 1.02/25.9
Length (C) - in/mm: 1.69/41.9
Z (ohms per bead - single turn 1 MHz): 45
Z (ohms per bead - single turn 5 MHz): 90
Z (ohms per bead - single turn 10 MHz): 125
Z (ohms per bead - single turn 25 MHz): 218
Z (ohms per bead - single turn 100 MHz): 375
Z ohms (per bead - single turn 250 MHz): 340
Case/Box lot size: 36

Also known as Big Clamp On. Very useful for AC/DC power, coax cable, etc. Use multiple turns for best results or multiple chokes in series (recommended for large amperage power cables). Always put +/- dc cables through the same ferrite filter so their fields cancel and the ferrite suppresses the common mode current on each cable.. Bulk pack of 3

Show More
Display prices in:USD

Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG