Off Center Fed (OCF) Dipole Baluns

Bullet 50:50 (1:1) HF Balun + Optional Dipole Kit - .1-61 MHz, 500 Watts PEP, up to 34 dB noise reduction!

SKU Bullet-1B-500EB
$79.95
Bulk pricing available for quantities of 2 units or more
Optional Wire Dipole Kit
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$74.956% off
10 items$64.9519% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
Bullet 50:50 (1:1) HF Balun + Optional Dipole Kit - .1-61 MHz, 500 Watts PEP, up to 34 dB noise reduction!
Product Details
UPC: Does not apply
Brand: Palomar Engineers
MPN: Bullet-1B-500EB
PEP Power Rating (watts): 500
Choking Impedance Range (ohms): up to 6000
Common Mode Attenuation (db): up to 38 dB
Estimated Insertion Loss (db): .1
Input Connector Type: SO-239
Output Connector Connector Type: Side Eyebolts

New improved version now goes down to 100 KHz and up to 61 MHz < 2:1 SWR. Choose Balun only or add optional dipole wire kit (wire, Insulators, Spade lugs for attachment to balun - assembly required). Center insulator and Balun in one case - 1/4" stainless hardware and 500 real watts rated!

The Bullet-1B-500EB is a multi-core current balun with built in feed line choke offering up to 34 dB of common mode current rejection (plenty for most applications) to keep RFI off the coax outer braid. The Bullet-1B-500EB is housed in a compact enclosure (looks like a bullet) that is lightweight and easy to transport for your portable/permanent antenna solution. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with dual side eye bolt output and wire strain relief. Rated 500 Watts PEP Watts from .1-61 MHz. Bullet-1B-500EB weight is .85 pounds (14 oz).

This balun/feedline choke keeps TRANSMIT RFI off the coax outer braid while transmitting. If your station suffers from common mode RFI noise on RECEIVE, then use one of our Common Mode Coax Noise Filters (such as the CMNF-500-50) that suppresses common mode noise on RECEIVE operations.

Make a FAN DIPOLE using optional dipole kits (e.g. 80/40 would use extra 40 meter dipole if you chose the 80 meter dipole lit for this listing).

NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 750 watts continuous or 1500 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.

Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.


Testimonial

Hi Bob,

Radio: Flex-6700 running barefoot -10 to 100 Watts max.
Antenna: MFJ-1216 – 160/80 meter OCFD wire antenna with matching network.
Elevation: Over 60 feet AGL – fully extended.
Installed: Mid November 2013

I operate mainly on the digital modes running less than 50 Watts.  All of the sudden after a few days operating with this antenna, I start to have RFI and my radio was acting up; such as changing bands, SWR changing values, radio failures and turning off. However, when I used my Hy-Gain 18 HT vertical on the same band none of the abnormality occurred.
I contacted MFJ and confirm that what I was noticing was a failure of their “matching network” AKA balun.  They offered no solutions. Then I contacted Palomar Engineers and bought the 1:1 new toroid RF beads.  I called Palomar Engineers and I happened to talked to you directly; regarding the on going issue with the MFJ antenna. I found out that the 1:1 balun was not what I needed (I was miss-informed by MFJ that it was 1:1 matching network.)
You offered to make the required balun 4:1 and the rest is history.

Here are my findings:

  1. No more RFI displayed on the monitors.
  2. Radio not acting up or turning off.
  3. The SWR at 160/80 meter is 1.2:1
  4. No antenna tuner required.  (radio goes to Bypass automatically.)
  5. Worst SWR is on 10 meter with a 2:1 but still usable, with antenna tuner 1.5.
  6. One happy OCFD user!

Thanks to Palomar Engineers design and engineering for solving this issue.

73, Ernest – W4EG