Model CB-6-1500 is a 6:1 (300:50) voltage balun housed in a Nema enclosure box (4″ x 4″ x 2″) with two top studs capable of input power levels up to 1.5KW PEP/500 watts continuous when used with a matched load. The 6:1 ratio takes 50 ohms input and matches to 300 ohms balanced output from 1.8-61 MHz with SWR < 1.5:1 under matched load conditions. A great balun for windoms, OCF antennas >60 feet over ground, Hertz and folded dipole antennas, T2FD etc. Dual core, Ruthroff style balun. Choose version with side eye bolts for wire attachments for OCF dipole use.
Snap On RF Choke/Isolator - 1/4"/6mm cable, RG-58/59/06/LMR240 - 3-300 MHz, -5/10/15 Bead OptionProduct DetailsBrand: Palomar EngineersMPN: SNO-1/4-5Effective Frequency Range (MHz): 3-300PEP Power Rating (watts): same as coax cable ratingChoking Impedance Range (ohms): 5 bead: 500-1000, 10 bead: 600-1800, 15 bead: 1000-2100Common Mode Attenuation (db): 5 bead: 16-22db, 10 bead: 17-25db, 15 bead: 21-27 dbEstimated Insertion Loss (db): .025Input Connector Type: noneOutput Connector Connector Type: noneGround Connector (Y/N): noneEnclosure Size (LxWxH inches): noneUse for 1/4″ Cable – RG-58, RG59, RG-6, LMR-240, etc
For 1/4” cables use five FSB31-1/4 split beads for 80-10 meters (3-30 mHz) or ten FSB31-1/4 split beads for 160-10 (1.8-30 MHz) meters or use 15 FSB31-1/4 for even higher choking for 1-10 MHz.
Typical Impedance per split bead: 10 MHz: 100 ohms, 25 MHz: 163 ohms, 100 MHz: 275 ohms, 250 MHz: 275 ohm
Select 10 bead version for 160 meter use. Minimum recommended total impedance is 500 ohms at frequency of interest.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
Use for 1/4″ Cable – RG-58, RG59, RG-6, LMR-240, etc
For 1/4” cables use five FSB31-1/4 split beads for 80-10 meters (3-30 mHz) or ten FSB31-1/4 split beads for 160-10 (1.8-30 MHz) meters or use 15 FSB31-1/4 for even higher choking for 1-10 MHz.
Typical Impedance per split bead: 10 MHz: 100 ohms, 25 MHz: 163 ohms, 100 MHz: 275 ohms, 250 MHz: 275 ohm
Select 10 bead version for 160 meter use. Minimum recommended total impedance is 500 ohms at frequency of interest.
The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips.
As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable.
Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.
