End Fed Long Wire Antennas

One of the most popular antennas today is the end fed long wire antenna due to it ease of installation, portability and stealth in various installations. It can be a condo dweller’s only access to the world of ham radio or the best alternative for a backpacking SOTA (Summits on the Air) mountaintop expedition.

The antenna is simple to deploy, folds up easily for transport, and weighs under a pound, yet, with the proper length of wire, can work the 80-10 meter bands easily with the built in antenna tuner of most current day transceivers. You will need several components for a successful deployment of the end fed antenna and these are shown in the diagram below:

End Fed Antenna Chain - End Fed Long Wire Antennas

 

Impedance Transformer - End Fed Long Wire AntennasThe antenna impedance matching components (BOX “Z” above) to match the antenna impedance to the coax line impedance (usually 50 ohms).  For non-resonant end fed  antennas, the typical feed point impedance is 300 to 600 ohms and a 9:1 impedance transformer (e.g. 450 ohm average antenna impedance to 50 ohm coax, also know as a 9:1 unun).  For do-it-yourself antenna builders, 9:1 impedance transformer  information is HERE

Feed Line Choke - End Fed Long Wire AntennasWith end fed antennas, the coax is meant to radiate as part of the antenna system (serving as the “ground” or counterpoise) and therefore you need to use a Feed line Choke (BOX “FC” above) to suppress the common mode current on the outside of the coax feed line so it does not enter the radio and cause garbled communication.. The Feed line (FC) acts as a stop sign for RF current flowing back on the outside of the coax.  The higher the choking resistance of the feed line choke, the less the coax braid RFI common mode current, and the less noise enters the radio.  Feed Line choke alternatives are HERE.

Radio System - End Fed Long Wire AntennasThe radio station is also a key component of the antenna system and has two functions: transmit and receive.  Matching the transmitter to the coax feed line is often done with an antenna tuner and receiver systems should be installed to maximize signal to noise ratio.  Reducing receiver noise is critical for weak signal reception and the use of coax noise filters AND receiver power supply lines (AC or DC) noise filters is usually needed for optimum reception. Reducing RFI generated by the radio station (you are the SOURCE of RFI) or received by your radio station (you are the VICTIM of RFI) is an important aspect of radio station operations.  Palomar Engineers has many solutions for RFI problems – Click HERE to develop alternative strategies depending on your particular situation.

Want to compare End Fed Antennas?  See: End Fed Antenna Secrets (PDF)

The “Bullet” End Fed Long Wire Antenna

The key to end fed antenna success is the matching network interface between the long wire antenna and the coax feed line and feed line choke at the transceiver.  Palomar Engineers employs a dual core matching system that offers wide bandwidth (1-61 MHz), 500 watt PEP rating, and a connection for a counterpoise or ground if desired.

The antenna can be used as a sloper, “L” with a vertical section and a longer horizontal section, or as a random horizontal antenna between two trees or supports.

Our network matching network is called the “Bullet” because of it shape and its effectiveness at taking down or contacting distant (DX) stations all over the world under the right conditions.  The Bullet uses all stainless steel connectors and a dual core ferrite 9:1 unun for higher power rating then many competitive products.

We sell the Bullet components separately so you can add you own wire type and length or you can purchase a complete antenna system including wire and end insulator.

 

SMART TV RFI/Noise Reduction Kit - AC Power + 4 I/O (HDMI, Audio) cables

SKU RFI-HDTV
$29.95
On Sale
List price $89.95 Save 67%
Bulk pricing available for quantities of 2 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$27.957% off
10 items$24.5018% off
50 items$21.9527% off
100 items$19.9533% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
SMART TV RFI/Noise Reduction Kit - AC Power + 4 I/O (HDMI, Audio) cables
Product Details
MPN: RFI-HDTV
Type: NEW
Country/Region of Manufacture: USA
Filter Power Rating (PEP watts): not applicable
RFI Suppression Range (MHz): 1-300 MHz

The RFI-HDTV RFI/Noise solution kit is specifically designed to cure most HDTV external interference issues triggered by Radio Frequency Interference problems generated by AM/FM, CB and Ham radio transmitters or other consumer electronic devices. The ferrite filters are selected to eliminate RFI from 1 to 300 MHz. The ferrites are easy to use, don’t require modification of the protected equipment and work in almost all cases.

What is included in the kit?

The RFI-HDTV kit contains a selection of ferrites including 1 ring filter for AC power and 4 3/8" snap on filters for input/output cables such as HDMI, video, cable/satellite input, audio, etc. RFI occurring at lower frequencies typically comes through the AC power lines acting as “antennas” picking up the interference signal and these ferrite filters have been specifically selected to suppress this interference. An instruction sheet is included with typical installation examples. This kit also works on computer monitors experiencing RFI.

If you have a sophisticated home theater systems with multiple devices such as DVD players, cable/satellite input, OTA antennas, audio amplifiers, consider the RFI-HTS which includes many more filters for multiple devices.

TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices.Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.

Typical RFI Problem/Solution:

Hello,
I am Larry, a ham operator and I am having interference issues with
my Direct TV system.
My station is a FT450D through an Ameritron ALS-600. From the amp
through a coax switch  to choose between an OCF dipole or an Hustler
5BTV vertical. Any power over 100 watts and my DTV goes off the air
and must completely reboot/format. Coax is RG-8. The DTV dish is
pointed away from the dipole and separated by about 25'. DTV was
totally useless! They suggested I not talk on the radio while she is
watching TV!  Please help me with a reasonable, cost effective
soultion. (The wife gets really pissed when I shutdown the tv!)

Thank you,

Larry 

Hi Larry,

Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.

The solutions are straight forward using our home theater system RFI kit.

 

Typical installations are shown below:

 

Bullet End Fed Antenna Notes (PDF)

CAUTION

USE CAUTION WHEN INSTALLING ANTENNA AND KEEP AWAY FROM ANY POWER LINE WIRES!