One of the most popular antennas today is the end fed long wire antenna due to it ease of installation, portability and stealth in various installations. It can be a condo dweller’s only access to the world of ham radio or the best alternative for a backpacking SOTA (Summits on the Air) mountaintop expedition.
The antenna is simple to deploy, folds up easily for transport, and weighs under a pound, yet, with the proper length of wire, can work the 80-10 meter bands easily with the built in antenna tuner of most current day transceivers. You will need several components for a successful deployment of the end fed antenna and these are shown in the diagram below:
The antenna impedance matching components (BOX “Z” above) to match the antenna impedance to the coax line impedance (usually 50 ohms). For non-resonant end fed antennas, the typical feed point impedance is 300 to 600 ohms and a 9:1 impedance transformer (e.g. 450 ohm average antenna impedance to 50 ohm coax, also know as a 9:1 unun). For do-it-yourself antenna builders, 9:1 impedance transformer information is HERE
With end fed antennas, the coax is meant to radiate as part of the antenna system (serving as the “ground” or counterpoise) and therefore you need to use a Feed line Choke (BOX “FC” above) to suppress the common mode current on the outside of the coax feed line so it does not enter the radio and cause garbled communication.. The Feed line (FC) acts as a stop sign for RF current flowing back on the outside of the coax. The higher the choking resistance of the feed line choke, the less the coax braid RFI common mode current, and the less noise enters the radio. Feed Line choke alternatives are HERE.
The radio station is also a key component of the antenna system and has two functions: transmit and receive. Matching the transmitter to the coax feed line is often done with an antenna tuner and receiver systems should be installed to maximize signal to noise ratio. Reducing receiver noise is critical for weak signal reception and the use of coax noise filters AND receiver power supply lines (AC or DC) noise filters is usually needed for optimum reception. Reducing RFI generated by the radio station (you are the SOURCE of RFI) or received by your radio station (you are the VICTIM of RFI) is an important aspect of radio station operations. Palomar Engineers has many solutions for RFI problems – Click HERE to develop alternative strategies depending on your particular situation.
Want to compare End Fed Antennas? See: End Fed Antenna Secrets (PDF)
The “Bullet” End Fed Long Wire Antenna
The key to end fed antenna success is the matching network interface between the long wire antenna and the coax feed line and feed line choke at the transceiver. Palomar Engineers employs a dual core matching system that offers wide bandwidth (1-61 MHz), 500 watt PEP rating, and a connection for a counterpoise or ground if desired.
The antenna can be used as a sloper, “L” with a vertical section and a longer horizontal section, or as a random horizontal antenna between two trees or supports.
Our network matching network is called the “Bullet” because of it shape and its effectiveness at taking down or contacting distant (DX) stations all over the world under the right conditions. The Bullet uses all stainless steel connectors and a dual core ferrite 9:1 unun for higher power rating then many competitive products.
We sell the Bullet components separately so you can add you own wire type and length or you can purchase a complete antenna system including wire and end insulator.
Coax Noise Filters
The Problem:
Common mode current induced by radiated sources (plasma TV, routers, computers, transmitters, etc.) can be picked up by the outside of the coax braid from the antenna feed point back to the receiver. This portion of the coax braid acts like a second receiving antenna, picking up common mode noise signals that combine with weak signals (traveling down the center conductor and inside of the coax braid) making it difficult or impossible to hear weak signals! See diagram below.
The Solution:
A coax common mode noise filter with high choking impedance at the receiver/transceiver end of the coax effectively reduces common mode noise present on the coax braid while passing desired signals present on the coax center conductor. For best results, and to reduce co-interference between choked and un-choked feed lines with multiple antennas, EACH antenna feed line entering the radio room needs to have a coax noise filter even if it feeds a common coax switch since most antenna switches ONLY switch the center conductor of the coax line, yet all the coax braids are ALWAYS connected together in parallel.So when an antenna is NOT SELECTED, its coax sheath still contributes to the noise level of the connected antenna through the common connector ground!
The solution? A common mode noise filter with high choking impedance at the receiver end of the coax.
Do you have common mode noise on your coax?
Make this simple test to find out.
- Remove the coax connector and measure the noise level.
- Now insert the coax connector CENTER CONDUCTOR ONLY into the SO-239 antenna input and measure the noise level (it should be higher and include possible signals)
- Now connect the OUTER SHELL of the coax connector to the antenna input and measure the noise level.If it is higher you have common mode noise and the common mode noise filter will help suppress this noise which is carried on the outside of the coax braid (acting as a second receive antenna).
Common mode noise suppression with the Palomar CMNF series of filters is typically 25-36 dB which is equivalent to 4-6 “S” units on radios with 6 dB/”S” unit or may be more on radios with 3dB/”S” unit.
Note for antenna switch users, perform the above test on each antenna coax lead separately to determine if that particular antenna braid is contributing noise to the receiver – use a coax noise filter on the antennas that have common mode noise.
Coax Common Mode Noise Test (pdf)
Typical installations are shown below:
Bullet End Fed Antenna Notes (PDF)
CAUTION
USE CAUTION WHEN INSTALLING ANTENNA AND KEEP AWAY FROM ANY POWER LINE WIRES!