Portable Operation RFI Kits

3136934587 - Portable Operation RFI Kits
+3

25-AMP (Peak) IN-LINE ELECTRONIC FILTER for 12 VOLTS DC, AUTOMOTIVE, RV RFI, ALTERNATOR, PULSE NOISE SUPPRESSION

RFI-N700
$49.95
In stock
1
Product Details
MPN: RFI-N25
Country/Region of Manufacture: USA

PURPOSE:The N-700 is an active electronic noise suppressor that employs a high density, low loss toroid 0.25 mH choke coupled with two power 2N3055 NPN power transistors in a capacitor multiplier configuration. The N-700 is designed to eliminate in-noise for Auto-sound Systems including: Alternator Whine, Fan Humming, ignition pops, etc.N-700 applications include Power Equalizers, Amplifiers, Cellular Phones, CB Radios, Two Way Communication Equipment, Amateur Radio Components, CD Players, and AM/FM Cassette Decks, etc.

FEATURES:The air cooled design of the N-700 filter permits maximum efficiency and effectiveness.The ferrite toroid core of the choke component of the L configuration is responsible for a very high rate of attenuation with very low line losses.The Beta of the power transistors multiples the capacitance to maximize the attenuation of the active filter. There are only three wires needed for the installation of the filter =Filter Input, Filter Output, and the Chassis Ground.The Chassis Ground is required to complete the circuit’s operation.

INSTALLATION:Make sure the noise is in-line before installing any in-line filter.A good confirmation would be to temporarily substitute a 120 VAC to a 12 VDC power supply, or a small 12 Volt motorcycle battery, for the vehicle's electrical system.If the noise goes away when the alternate power supply is connected, then you have a case of in-line noise.

To get optimum results with the N-700, the following directions should be followed:

1.Cut the component's main power lead between the fuse and the component.

2. Connect the GREEN wire to the fuse side of the cut (Source). If no fuse is present, be sure to add a fuse to this connection. Be sure to add a fuse rated at 10 Amps or less to protect the vehicle.

3.Connect the RED wire to the component side (Load). This output lead is also fused to protect the N-700.

4.Connect the BLACK wire to a good chassis ground.The N-700 will not function without a connection to chassis ground.

Practical and easy to install, the N-700 is one of the most versatile and effective filters on the market.

Save this product for later
Display prices in: USD
Portable operation is fun but also brings challenges to the radio operator concerning receiver “noise” levels, RF interference from adjacent sources including close by transmitting stations, and RFI from portable generators.  A typical scenario and some suggested Palomar product solutions are shown in the picture below:

Generator RFI testimonial:

Bob 

Received your order in a timely fashion. Tried the generator kit on Sunday & it drops the noise from S9 to S5 and 
took out all the electrical noise.  I may want some more toroids from you at some point for other interference problems
I have  here.
Ken VE3KCY

Using an amplifier?  Don’t forget our Linear Amplifier RFI Kits

Want to make up your own RFI kits for a particular operation? Here are links to some of  typical RFI solutions used in portable operations:

AC/DC common mode filters

Feed Line chokes

Coax Noise Filters

If you use a computer for logging in your portable operations, RFI getting into computers will often lock up your computer and/or radio and a computer RFI suppression kits may be helpful

Computer RFI Kits

Make your expedition or portable operation a pleasant and fun outing and remember to take along your RFI kits so you have more time to operate rather then to troubleshoot intermittent or noisy receiver conditions.

Portable Antenna Kits

If you need an effective portable antenna which folds up for transport yet is easy to deploy at your operating site, consider the BULLET series of end fed wire antennas.

BULLET Antennas (click on link or picture for more info)

Bullet Antenna Product 300x292 - Portable Operation RFI Kits