Wall Wart RFI Noise Filter

1653144023 - Wall Wart RFI Noise Filter
+3

Off Center Fed (OCF) 4:1 Balun and 1:1 Balun Combo, 1.8-61 MHz, 1.5/5KW PEP Option

CB-4-1500OCF
$139.95
In stock
1
Product Details
MPN: CB-4-1500OCF, CB-4-3000OCF, CB-4-5000OCF
Country/Region of Manufacture: USA
Input ohms/Output ohms: 50 in/200 out
Frequency Range < 2:1 SWR (MHz): 1.8-61 MHz for 1.5KW, 1.8-31 MHz for 3KW/5KW
PEP Power Rating (watts): 1.5KW/3KW/5KW
Enclosure Size: 4"x4"x 2"(1.5KW), 6"x 6" x 4"(3KW/5KW)
Weight (pounds): 3(1.4KW)/4(3KW)/5(5KW)

1500 Watt PEP rated 4:1 Current Balun + internal 1:1 Current Balun in one enclosure

After many requests we have created a compact, special balun for OCF and loop (Skyloop or Delta loop) antennas. The CB-4-1500OCF is a CUBE enclosure containing a multi-core, broadband 4:1 impedance transformer in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 450 watts CW/FT8/RTTY (ICAS). 1.8Mhz – 61 MHz.

The CB-4-5000OCF (5KW PEP) have a frequency range of 1.8-31 MHz and does not cover 6 meters.

CB-4-1500OCF is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist. Use this balun combination when you DO NOT have a vertical radiator.

5KW are in 6" x 6" x 4" enclosure. 1.5KW is 3 pounds, 5KW is 5 pounds. Note the 5KW models are made to order and shipment time is approximately 7-10 days after order date.

For a 135 foot 80 meter OCF, we recommend a 29.5%/79.5% offset for best all band results. If you use 66%/34% offset, do not use on 15 meters as the impedance mismatch may damage the balun under high power operations

Save this product for later
Display prices in: USD
Wall Wart switching DC power supplies that plug into the AC power line plug and provide DC power to laptops, routers, battery chargers, cell phone chargers, etc are a known source of broadband RFI (a.k.a dirty electricity) that effects many electrical devices including computers, radio receivers, HDTV systems, etc.  In many cases this extra RFI noise effects computer I/O speeds since they have to error correct the information packets many more times due to the noise interference causing packet errors.  A ferrite ring can often increase data throughput by reducing the error correction to normal rates.

A simple ferrite ring filter on the DC power line can help suppress the RFI noise affecting the victim device or keep the DC power cord from acting as an antenna and radiating RFI into other victim devices. This kit is also useful on laptop computer supplies, routers, cable modems, wireless phone charges, etc.

RFI WW Installation 300x288 - Wall Wart RFI Noise Filter

Installation is quick and easy: Just wrap the DC power cord through the center of the ring filter as many times as you can and reinstall.  For best results with long DC power lines, use one at the ring filter at the wall wart end (to prevent the wall wart power supply from using the DC line as an antenna) and another at the DC plug end (to prevent the electronics in the powered device from using the DC power cord as an antenna).  Typical installation is shown below:

The filter suppresses RFI in from .1-100 MHz.   Inside diameter is 3/4 inch/19 mm.

Since most households and office environments have multiple wall warts we offer the Wall Wart RFI Filter kit in bulk quantity packages.

Known RFI Generators include Roku/Sling-TV power adapter - Interference heard in the AM broadcast band
 and harmonics.
Also many ethernet Cable/DSL modems, cell phone chargers, computer power adapters have the same issue:
using the AC or DC side of the power supply as a radiating antenna.

RFI solution is to use a linear power supply, change adapters or wall wart ferrite filters