Ladder Line to coax transformers
Ladder Line baluns are used to match the impedance seen at the end of the ladder line to a coaxial cable, usually 50 ohms, but a ladder line balun can also be used to match to 75 ohm coax like RG-6/U used for cable and satellite installations. While RG-6 doesn’t have the same power rating as larger cable, it is very useful for beverage antennas or receiving antennas which don’t carry a lot of power.
The impedance seen at the end of the ladder line will not be the same as the characteristic impedance of the ladder line (typically 300 or 450 ohms). Good ladder line antenna designs try to have the impedance at the end of the ladder line attachment to the balun close to 200 ohms so that a 4:1 balun can be used to match to 50 ohm coax.
A typical ladder line antenna is shown in the picture below:
Palomar Engineers has ladder line to coax 4:1 baluns in both kit form and also assembled in a variety of 1 watt to 10KW power levels to suit the needs of many customers. The ladder line baluns are designed for balanced output and are generally used at the end of a run of ladder line from the antenna. The baluns connect to the ladder line and then transition to coax cable to you antenna tuner or radio station.
Refine by 
MAXI-CHOKER Coax Line Isolator/Balun, 1-61 MHz, 1.5/3KW, SO-239 In/Stud Output, FLAGPOLE OCF, G5RV, ZS6BKW, BN4000 Replacement, Ladder Line-Coax interfaceMAXI-CHOKER Coax Line Isolator/Balun, 1-61 MHz, 1.5/3KW, SO-239 In/Stud Output, FLAGPOLE OCF, G5RV, ZS6BKW, BN4000 Replacement, Ladder Line-Coax interfaceSKU MC-1-1500LL$89.95
Ladder Line to coax transformers
Ladder Line baluns are used to match the impedance seen at the end of the ladder line to a coaxial cable, usually 50 ohms, but a ladder line balun can also be used to match to 75 ohm coax like RG-6/U used for cable and satellite installations. While RG-6 doesn’t have the same power rating as larger cable, it is very useful for beverage antennas or receiving antennas which don’t carry a lot of power.
The impedance seen at the end of the ladder line will not be the same as the characteristic impedance of the ladder line (typically 300 or 450 ohms). Good ladder line antenna designs try to have the impedance at the end of the ladder line attachment to the balun close to 200 ohms so that a 4:1 balun can be used to match to 50 ohm coax.
A typical ladder line antenna is shown in the picture below:
Palomar Engineers has ladder line to coax 4:1 baluns in both kit form and also assembled in a variety of 1 watt to 10KW power levels to suit the needs of many customers. The ladder line baluns are designed for balanced output and are generally used at the end of a run of ladder line from the antenna. The baluns connect to the ladder line and then transition to coax cable to you antenna tuner or radio station.
Christmas lights or yard lights with switching DC power supplies are often the RFI source and a clamp on ferrite bead on the AC AND the DC side feeding the lights is needed to help suppress the switching power supply RFI noise. Suitable snap on beads are FSB31-1/2 for the 1-250 MHz range.
We have also had reported wireless HDTV boxes, and FOSCAM and AMCREST security camera systems causing RFI to garage door remote openers. Use our Garage Door Opener RFI kit to suppress the interference to the opener (VICTIM) – you need one kit for each opener. Maximize the distance from the camera to the openers may also help. Additionally shield cable to the garage door sensors may be needed depending on severity of the camera RFI.
Obvious Tech Note: make sure your remote batteries have enough energy to activate the GDO or the signal they transmit may not be large enough to over ride the RFI signal, but a fresh battery may be able to overcome the weak RFI source and allow the GDO to operate correctly.