Hybrid 2:25 Current Balun + 1:1 Current Balun in one enclosure, 1.8-61 MHz, 1.5/5KW PEP - Loop AntennaProduct DetailsMPN: CB-2.25-1-1500/5000EB or TS optionCountry/Region of Manufacture: USAInput ohms/Output ohms: 50 in/112.5 outFrequency Range < 2:1 SWR (MHz): 1.8-61 MHzPEP Power Rating (watts): 1.5KW or 5KWEnclosure Size: 4"x4"x 2"(1.5KW), 6"x6"x4" (5KW)Weight (pounds): 3 (1.5KW), 5 (5KW)Antenna Compatability: Single Band Loop
After many requests we have created a compact, special balun for single band loop (Sky loop or Delta loop) antennas. The CB-2.25-1500 is a CUBE(TM) enclosure containing a multi-core, broadband 2:25 impedance transformer (50 ohm coax input to 112.5 ohm balanced output) in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 450 watts CW (ICAS). 1.8Mhz – 61 MHz.
CB-2.25-1-1500EB is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist. Also available with top studs for post or wall mounting (Model # CB-2.25-1-1500TS)
Loop antennas should be cut for 1005/F(MHz) in total length, where F (MHz) is the lowest frequency to be used. For 3.5MHz this equates to 288 foot perimeter (square, delta, multi-side ok).
Production Note: These hybrid baluns are special order and made to order for each customer. Please note that shipping will be approximately 2-3 weeks after order placed depending upon our existing production schedule.
Pictures show 2-1 balun but you will receive the 2.25:1 balun with 1:1 hybrid in a single enclosure.
After many requests we have created a compact, special balun for single band loop (Sky loop or Delta loop) antennas. The CB-2.25-1500 is a CUBE(TM) enclosure containing a multi-core, broadband 2:25 impedance transformer (50 ohm coax input to 112.5 ohm balanced output) in series with a 1:1 current balun for extra common mode current choking to keep RF current off the outside of the coax braid and on the antenna where it belongs. The extra choking action also means that the coax feed line will not act as a radiator causing unnecessary RF interference (RFI). Rated for full 1500 watts PEP and 450 watts CW (ICAS). 1.8Mhz – 61 MHz.
CB-2.25-1-1500EB is housed in a 4” x 4” x 2” waterproof housing with SO-239 input and stainless steel eye bolts on the side for ease of connection to your wire antenna. Top eye bolt acts as an antenna hoist. Also available with top studs for post or wall mounting (Model # CB-2.25-1-1500TS)
Loop antennas should be cut for 1005/F(MHz) in total length, where F (MHz) is the lowest frequency to be used. For 3.5MHz this equates to 288 foot perimeter (square, delta, multi-side ok).
Production Note: These hybrid baluns are special order and made to order for each customer. Please note that shipping will be approximately 2-3 weeks after order placed depending upon our existing production schedule.
Pictures show 2-1 balun but you will receive the 2.25:1 balun with 1:1 hybrid in a single enclosure.
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer