Bullet 50:100 (2:1) HF Balun, .1-61 MHz, 500/1500 Watts PEP, Loop AntennaProduct DetailsMPN: Bullet-2B-500/Bullet-2B-1500Country/Region of Manufacture: USAType: NEWInput ohms/Output ohms: 50 in, 100 outFrequency Range < 2:1 SWR (MHz): .1-61 MHz < 2 SWRPEP Power Rating (watts): 500/1500Input Connector: SO-239Output Connector(s): Side EyeboltsHardware Type: Stainless SteelWeight (pounds): 1Antenna Compatability: Full Wave LoopNew improved version now goes down to 100 KHz and up to 61 MHz < 2:1 SWR!
The Bullet-2B is a multi-core balun with a compact enclosure (looks like a bullet) enclosure that is lightweight and easy to transport for your portable loop antenna solution. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Rated 500 Watts PEP Watts from .1-61 MHz. DC grounded to coax shield for static bleed off.
This transformer requires a feed line choke at the balun to isolate the coax feed line from the antenna. A coax noise filter is also recommended at the radio end of the coax..
Loop Antennas
Loop antennas are some of the best radiating and receiving antennas you can make. They can be in a triangle (called a delta loop), square or rectangle or even a circle. Horizontal loops can be fed anywhere that is convenient. Vertical delta loops(circumference length=1005/f(Mhz) are best fed 1/4 wavelength (length=246/f(Mhz)) from the top point down one side.
We offer pre-configured loop wire kits for your antenna building convenience. Just choose the band you need - see related products.
Want multiple bands from a loop antenna, consider the 4;1 Bullet (Bullet-4BEB in 500 or 1500 watts versions).
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.
Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
New improved version now goes down to 100 KHz and up to 61 MHz < 2:1 SWR!
The Bullet-2B is a multi-core balun with a compact enclosure (looks like a bullet) enclosure that is lightweight and easy to transport for your portable loop antenna solution. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Rated 500 Watts PEP Watts from .1-61 MHz. DC grounded to coax shield for static bleed off.
This transformer requires a feed line choke at the balun to isolate the coax feed line from the antenna. A coax noise filter is also recommended at the radio end of the coax..
Loop Antennas
Loop antennas are some of the best radiating and receiving antennas you can make. They can be in a triangle (called a delta loop), square or rectangle or even a circle. Horizontal loops can be fed anywhere that is convenient. Vertical delta loops(circumference length=1005/f(Mhz) are best fed 1/4 wavelength (length=246/f(Mhz)) from the top point down one side.
We offer pre-configured loop wire kits for your antenna building convenience. Just choose the band you need - see related products.
Want multiple bands from a loop antenna, consider the 4;1 Bullet (Bullet-4BEB in 500 or 1500 watts versions).
NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.
Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer