50:250 ohm (5:1) CUBE™ Unun™, 1.8-61 Mz, 1500 Watts, end fed, verticalProduct DetailsMPN: CU-5-1500Input ohms/Output ohms: 50 in / 250 outputFrequency Range < 2:1 SWR (MHz): 1-31PEP Power Rating (watts): 1500Model CU-5-1500EB- 5 to 1 Unun
(SO-239 in/Eye bolt hoist with output connector on top, side stud for ground/counterpoise)
Purpose. This unun is designed to match 250 ohms unbalanced to 50 ohms unbalanced up to 1500 watts PEP power from 1.8-61 MHz. It provides conversion from unbalanced 50 ohm coax to an unbalanced 250 ohm load/antenna feed point and gives a 5:1 impedance step-up to reduce VSWR on the coax feed line. The unun is housed in a 4” x 4” X “2 NEMA weather resistant box with SO-239 coaxial input and a ¼” stud terminal with wing nut on the top for output and another on the side for ground or counterpoise connection.
This unun is DC grounded and will bleed off static electricity but it is NOT A LIGHTNING ARRESTOR.
Model CU-5-1500 is a 50 ohm to 250 ohm (5:1) voltage unun used to translate a 50 ohm input up to 250 ohms at RF power levels up to 1500 watts PEP (30% duty cycle) when used with a matched load. With a matched 250 ohm unbalanced load SWR should not exceed 2.0 over the frequency range 1.8-61 MHz.
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 balun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical Antenna System Using CU-5-1500
Use a coax noise filter to reduce noise from any vertical antenna or a line isolator to suppress coax cable braid radiation on transmit.
On Sale
Snap On RF Choke/Isolator - 1/2"/12.7mm cable -5/10/15 Bead Option, 3-300 MHzSnap On RF Choke/Isolator - 1/2"/12.7mm cable -5/10/15 Bead Option, 3-300 MHzSKU SNO31-1/2-5List price $29.95 Save 13%$25.95
Model CU-5-1500EB- 5 to 1 Unun
(SO-239 in/Eye bolt hoist with output connector on top, side stud for ground/counterpoise)
Purpose. This unun is designed to match 250 ohms unbalanced to 50 ohms unbalanced up to 1500 watts PEP power from 1.8-61 MHz. It provides conversion from unbalanced 50 ohm coax to an unbalanced 250 ohm load/antenna feed point and gives a 5:1 impedance step-up to reduce VSWR on the coax feed line. The unun is housed in a 4” x 4” X “2 NEMA weather resistant box with SO-239 coaxial input and a ¼” stud terminal with wing nut on the top for output and another on the side for ground or counterpoise connection.
This unun is DC grounded and will bleed off static electricity but it is NOT A LIGHTNING ARRESTOR.
Model CU-5-1500 is a 50 ohm to 250 ohm (5:1) voltage unun used to translate a 50 ohm input up to 250 ohms at RF power levels up to 1500 watts PEP (30% duty cycle) when used with a matched load. With a matched 250 ohm unbalanced load SWR should not exceed 2.0 over the frequency range 1.8-61 MHz.
Application. For traveling wave, end fed or portable 20-31 foot vertical antennas the 5:1 balun makes a good transformer for converting 50 ohm coax to a 250 ohm feed point. If you use the antenna on multiple bands, the feed point impedance may not always be 250 ohms and use of the unun at high (>350 ohms) or low (<100 ohms) will require reduced power input or the unun may have its power ratings exceeded and damage to the unun may occur. The (5:1 conversion ratio will change for loads other than 250 ohms unbalanced.
Typical Antenna System Using CU-5-1500
Use a coax noise filter to reduce noise from any vertical antenna or a line isolator to suppress coax cable braid radiation on transmit.
TECH NOTE: We also stock RFI kits to protect effected devices such as garage door openers, computers (laptops, desktops), dsl/cable routers, ethernet hubs and many more devices. If you run a high powered RF amplifier in your ham station also consider a linear amp RFI kit which will cut down RFI transmitted by your station. Remember there is always a “transmitter” and a “receiver” of RFI and the quest is to find and choke the “path” the RFI has selected – you need to add ferrites to both the transmitting side and the receiving side to eliminate RFI problems. The RFI-HTS kit only helps suppress RFI on the receiving side.
Typical RFI Problem/Solution:
Hello, I am Larry, a ham operator and I am having interference issues with my Direct TV system. My station is a FT450D through an Ameritron ALS-600. From the amp through a coax switch to choose between an OCF dipole or an Hustler 5BTV vertical. Any power over 100 watts and my DTV goes off the air and must completly reboot/format. Coax is RG-8. The DTV dish is pointed away from the dipole and separated by about 25'. DTV was totally useless! They suggested I not talk on the radio while she is watching TV! Please help me with a reasonable, cost effective soultion. (The wife gets really pissed when I shutdown the tv!) Thank you, Larry
Hi Larry,
Your RFI problem is quite common and is usually a sign of either a radiating coax feed line or reception of your radiated signal (source) by the Direct TV (the victim) through either the AC power lines acting as “antennas” for your ham signal or the coax braid of the satellite antenna acting as an antenna for your signal.
The solutions are straight forward:
1. To make sure your feed line is not radiating you need a feed line choke at each antenna feed point (also makes your antenna work better since it is not using the coax as part of the antenna). You can use our simple Kit 110 with 5 snap on chokes on each antenna for this purpose. Part # Kit 110 at $27.50 each – one for each antenna. These chokes will keep your feed line from radiating and coupling into your ac power lines. INFO HERE
2. The radiation from your antennas themselves may also be getting into the ac power lines and coax braid of the Direct TV antenna so you need to protect the victim receiver. Depending upon the sophistication of your direct TV setup (e.g. home theater, dvd, tape player, sub woofer speakers, etc), the path of the RFI may be coming thru the AC power lines of any connected device to the video including the video monitor itself! To help solve this problem we have a home theater RFI kit for up to 5 devices (you need a minimum of two – one for the Direct TV receiver(AC and coax input) and another for the video monitor AC power lines and HDMI or video input cable. Our kit part # is RFI-HTS. INFO HERE
These items should help reduce the RFI and let you operate on the air while your wife watches TV.
Bob Brehm, AK6R
Chief Engineer