30-AMP (PEAK) IN-LINE TOROIDAL DC NOISE FILTER for 12 VOLTS, ALTERNATOR, PULSE NOISE SUPPRESSIONProduct DetailsMPN: RFI-N25Country/Region of Manufacture: USAPURPOSE:The N-25 is a passive noise suppressor that employs a high density, low loss toroid 0.25mH choke designed to eliminate in-line noise for Auto-sound, Avionics, and ham radio/CB/Two-Way communication systems including: Alternator Whine, Fan Hums, Dodge Ram Cummings Torque Converter Clutch Cycling Repair*, etc.The N-25 applications include Power Equalizers, Small Amplifiers, Cellular Phones, CB Radios, Two Way Communication Equipment, CD Players, and AM/FM Cassette Decks, etc.
FEATURES:The air-cooled design of the N-25 filter permits maximum efficiency and effectiveness.The ferrite toroid core of the choke component of the L configuration is responsible for a very high rate of attenuation with very low line losses.There are only three wires needed for the installation of the passive filter -Filter Input, Filter Output, and the Chassis Ground.
INSTALLATION:Make sure the noise is in-line before installing an in-line filter such as the N-25.A good confirmation would be to temporarily substitute a 120 VAC to a 12 VDC power supply, or a 12 Volt motorcycle battery, for the vehicle's electrical system.If the noise goes away when the alternate power supply is connected, then you have a case of in-line noise.
To get optimum results with the N-25, the following directions should be followed:
1.Cut the component's main power lead between the fuse and the component.
2. Connect the Green wire to the fuse side. (If there is no fuse, add one --- 10 Amps is recommended)
3.Connect the fused Red wire to the component side.
4.Connect the Black wire to a good chassis ground.
Practical and easy to install, the N-25 is one of the most versatile and effective filters on the market.
Note: The 30-Amp rating is instantaneous = peak… not constant. Fuse the Green lead with a 5 to 10-Amp fuse. Average current draw should be no larger than the fuse size of 10 amps.
PURPOSE:The N-25 is a passive noise suppressor that employs a high density, low loss toroid 0.25mH choke designed to eliminate in-line noise for Auto-sound, Avionics, and ham radio/CB/Two-Way communication systems including: Alternator Whine, Fan Hums, Dodge Ram Cummings Torque Converter Clutch Cycling Repair*, etc.The N-25 applications include Power Equalizers, Small Amplifiers, Cellular Phones, CB Radios, Two Way Communication Equipment, CD Players, and AM/FM Cassette Decks, etc.
FEATURES:The air-cooled design of the N-25 filter permits maximum efficiency and effectiveness.The ferrite toroid core of the choke component of the L configuration is responsible for a very high rate of attenuation with very low line losses.There are only three wires needed for the installation of the passive filter -Filter Input, Filter Output, and the Chassis Ground.
INSTALLATION:Make sure the noise is in-line before installing an in-line filter such as the N-25.A good confirmation would be to temporarily substitute a 120 VAC to a 12 VDC power supply, or a 12 Volt motorcycle battery, for the vehicle's electrical system.If the noise goes away when the alternate power supply is connected, then you have a case of in-line noise.
To get optimum results with the N-25, the following directions should be followed:
1.Cut the component's main power lead between the fuse and the component.
2. Connect the Green wire to the fuse side. (If there is no fuse, add one --- 10 Amps is recommended)
3.Connect the fused Red wire to the component side.
4.Connect the Black wire to a good chassis ground.
Practical and easy to install, the N-25 is one of the most versatile and effective filters on the market.
Note: The 30-Amp rating is instantaneous = peak… not constant. Fuse the Green lead with a 5 to 10-Amp fuse. Average current draw should be no larger than the fuse size of 10 amps.
