Broad Band Terminated Dipoles (BBTD, T2FD)

Broad Band Terminated Dipoles (BBTD), Tilted Terminated Fold Dipoles (T2FD) and Balanced Termination Folded Dipole BTFD) antennas can be designed to cover a large range of frequencies between 1.8 30 MHz.  Longer length antennas generally provide better low frequency efficiency but take up a larger footprint of land.   One BBTD that has worked well at the AK6R antenna farm is shown below.  Many other designs are available and can be found at www.HFLINK.COM as well as other internet sites.  Your mileage may vary using this antenna, but as a general coverage antenna for ham and shortwave broadcast, the simplicity can’t be beat even though an individual dipole on a specific band may out perform this broad band dipole.  Palomar Engineers has all the parts you need to build this antenna, so why not give it a try?

BBTD at AK6R 1024x726 - Broad Band Terminated Dipoles (BBTD, T2FD)

 

Depending on the source of the antenna design, different value baluns are specified.  Our Bullet(TM) baluns in ratios of 9:1, 12:1 and 16:1 are excellent for this type of antenna as they are broadband from 1.8-61 MHz and will take up to 500 watts PEP.

4222605654 - Broad Band Terminated Dipoles (BBTD, T2FD)
+3

MINI-BALUN 1:1 Coax Interface to Ladder Line, Dipole elements, 500 Watts PEP, up to -38Db Common Mode Rejection, 1-61 MHz, Flagpole, Dipole, Beam and G5RV/ZS6BKW Antennas

MB-1-500SS
$69.95
In stock
1
Product Details
Brand: Palomar Engineers
MPN: MC-1-500SS
Country/Region of Manufacture: United States
Effective Frequency Range (MHz): 1.8-60
PEP Power Rating (watts): 500 SSB (25% duty cycle), 250 Watts CW/FT8 (50% duty cycle)
Common Mode Attenuation (db): 20-38db
Estimated Insertion Loss (db): .25 db
Input Connector Type: SO-239 female
Output Connector Connector Type: Dual 1/4" stainless steel studs
Ground Connector (Y/N): none
Enclosure Size (LxWxH inches): 3" long, 2 in wide, 1.25" high

MINI-BALUN Features:

- Uses proprietary Multi-Turn ferrite technology for maximum choking (up to -38 dB common mode noise rejection) and maximum bandwidth

- 500 Watts PEP, 50 ohm SO-239 connectors In, Dual Side Stud Output, 1.8-61 MHz (usable to 100 MHz) - AKA 1:1 BALUN

- Works for all coax fed antennas from 1.8-61 MHz (160-6 meters) - excellent for multi-band beam interface, G5RV/ZS6BKW or Flag Pole OCF antennas fed with ladder line.

- 2-5 times more common mode noise rejection, wider bandwidth and higher power then competing isolators

MINI-CHOKER feed line chokes are used to suppress common mode current carried on the outside of the coax braid which is often responsible for receiver noise and RFI in the receiver/transmitter. These chokes are very useful for suppressing RFI common mode current at the antenna feed point, at 1/2 wavelength intervals along the coax feed line and also at the entrance to the radio station.

This choke has a SO-239 input and 1/4" top studs output.

For Higher Power needs use our MAXI-CHOKER with dual stud outputs in 1.5KW or 3KW version part# MC-1-1500LL, MC-1-3000LL

If you need a unbalanced output (SO239 output) instead of a balanced stud output, see MC-1-500 with SO239 output and input..






Save this product for later
Display prices in: USD

Likewise Termination Resistor values vary from 500-1250 ohms and we have a good selection shown HERE: