Broad Band Terminated Dipoles (BBTD, T2FD)

Broad Band Terminated Dipoles (BBTD), Tilted Terminated Fold Dipoles (T2FD) and Balanced Termination Folded Dipole BTFD) antennas can be designed to cover a large range of frequencies between 1.8 30 MHz.  Longer length antennas generally provide better low frequency efficiency but take up a larger footprint of land.   One BBTD that has worked well at the AK6R antenna farm is shown below.  Many other designs are available and can be found at www.HFLINK.COM as well as other internet sites.  Your mileage may vary using this antenna, but as a general coverage antenna for ham and shortwave broadcast, the simplicity can’t be beat even though an individual dipole on a specific band may out perform this broad band dipole.  Palomar Engineers has all the parts you need to build this antenna, so why not give it a try?

BBTD at AK6R 1024x726 - Broad Band Terminated Dipoles (BBTD, T2FD)

 

Depending on the source of the antenna design, different value baluns are specified.  Our Bullet(TM) baluns in ratios of 9:1, 12:1 and 16:1 are excellent for this type of antenna as they are broadband from 1.8-61 MHz and will take up to 500 watts PEP.

541337188 - Broad Band Terminated Dipoles (BBTD, T2FD)
+3

Icom 7400/7410/7600/7610/7700 Transceiver RFI and Noise Reduction Kit, RFI Range 1-60 MHz, 14 Filters

RFI-ICOM-7610
$89.95
In stock
1
Product Details
MPN: RFI-ICOM-7610
Type: NEW
Country/Region of Manufacture: United States
RFI Suppression Range (MHz): 1-60 MHz
# Ferrite Filters: 14
Enclosure Size (inches): n/a
Typical Use:: AC/DC power, RF output x 2, multiple I/O lines

Icom 7400/7600/7610/7700 RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the coax output of your radio, the AC/DC power, USB, ALC/Send, mouse,mic and additional interconnect cables. Kit has 4 ferrite ring filters and 10 ferrite snap on filters and instruction manual.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.

3. RFI to your other radios, audio/video systems, computers, telephones, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line and a coax noise filter at the radio end of the coax to reduce common mode noise.


If you use a linear amplifier use an amplifier RFI kit for additional RFI interference suppression.

Note: Icom 7300 picture shown which is typical of filters and connection cables.
Save this product for later
Display prices in: USD

Likewise Termination Resistor values vary from 500-1250 ohms and we have a good selection shown HERE: