Broad Band Terminated Dipoles (BBTD, T2FD)

Broad Band Terminated Dipoles (BBTD), Tilted Terminated Fold Dipoles (T2FD) and Balanced Termination Folded Dipole BTFD) antennas can be designed to cover a large range of frequencies between 1.8 30 MHz.  Longer length antennas generally provide better low frequency efficiency but take up a larger footprint of land.   One BBTD that has worked well at the AK6R antenna farm is shown below.  Many other designs are available and can be found at www.HFLINK.COM as well as other internet sites.  Your mileage may vary using this antenna, but as a general coverage antenna for ham and shortwave broadcast, the simplicity can’t be beat even though an individual dipole on a specific band may out perform this broad band dipole.  Palomar Engineers has all the parts you need to build this antenna, so why not give it a try?

BBTD at AK6R 1024x726 - Broad Band Terminated Dipoles (BBTD, T2FD)

 

Depending on the source of the antenna design, different value baluns are specified.  Our Bullet(TM) baluns in ratios of 9:1, 12:1 and 16:1 are excellent for this type of antenna as they are broadband from 1.8-61 MHz and will take up to 500 watts PEP.

4029027005 - Broad Band Terminated Dipoles (BBTD, T2FD)
+3

HF Mobile Transceiver RFI and Noise Reduction Kit, RFI Range 1-300 Mz

RFi-HF-MOBILE
$39.95
In stock
1
Product Details
MPN: RFI-HF-MOBILE
Type: NEW
Country/Region of Manufacture: United States
Filter Power Rating (PEP watts): 500
RFI Suppression Range (MHz): 1-300 MHz
# Ferrite Filters: 5
Enclosure Size (inches): n/a
Typical Use:: AC/DC power, RF output, 3 additional I/O lines

Palomar Engineers RFI Filter Kit for HF Base Radio Mobile Transceivers up to 300 MHz

BUY THIS KIT NOW TO SOLVE YOUR RFI/EMI NEEDS! WORKS WITH MANY BRANDS OF HAM/COMMERCIAL RADIO RIGS


Purpose

The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable. Additional chokes are included to reduce common mode currents on 3 more transceiver cables including computer control, audio and another.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to neighbor’s electronic devices including audio/video systems, computers, telephones, garage door openers, etc.

3. RFI to your other radios, audio/video systems, computers, telephones, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and a linear amp and between transceiver and antenna tuner or direct to antenna. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

Included are the following chokes and installation guidelines:

RF Input/Output: F240 for toroid balun – 5-9 turns of RG-58/RG-8X size coax cable through center

DC Input: F240 – 3-7 turns of DC power cable

3 additional I/O cables - 1/2 snap on for 1-2 turns through center. Multiple wires can share the same filter.

For additional RFI suppression, use a feed line choke at the antenna feed point to suppress common current on the coax feed line.


If you use a linear amplifier use an amplifier RFI kit for additional RFI interference suppression.
Save this product for later
Display prices in: USD

Likewise Termination Resistor values vary from 500-1250 ohms and we have a good selection shown HERE: