Broad Band Terminated Dipoles (BBTD, T2FD)

Broad Band Terminated Dipoles (BBTD), Tilted Terminated Fold Dipoles (T2FD) and Balanced Termination Folded Dipole BTFD) antennas can be designed to cover a large range of frequencies between 1.8 30 MHz.  Longer length antennas generally provide better low frequency efficiency but take up a larger footprint of land.   One BBTD that has worked well at the AK6R antenna farm is shown below.  Many other designs are available and can be found at www.HFLINK.COM as well as other internet sites.  Your mileage may vary using this antenna, but as a general coverage antenna for ham and shortwave broadcast, the simplicity can’t be beat even though an individual dipole on a specific band may out perform this broad band dipole.  Palomar Engineers has all the parts you need to build this antenna, so why not give it a try?

BBTD at AK6R 1024x726 - Broad Band Terminated Dipoles (BBTD, T2FD)

 

Depending on the source of the antenna design, different value baluns are specified.  Our Bullet(TM) baluns in ratios of 9:1, 12:1 and 16:1 are excellent for this type of antenna as they are broadband from 1.8-61 MHz and will take up to 500 watts PEP.

539851042 - Broad Band Terminated Dipoles (BBTD, T2FD)
+3

Generic Marine HF Radio RFI and Noise Reduction Kit, RFI Range 1-60 MHz - Icom, Furuno, SGC

RFI-HF-MARINE
$89.95
In stock
1
Product Details
MPN: RFI-HF-BASE
Type: NEW
Country/Region of Manufacture: United States
Filter Power Rating (PEP watts): 500
RFI Suppression Range (MHz): 1-300 MHz
# Ferrite Filters: 5
Enclosure Size (inches): n/a
Typical Use:: AC/DC power, RF output, 3 additional I/O lines

BUY THIS KIT NOW TO REDUCE NOISE IN THE RECEIVER AND SUPPRESS INTERFERENCE TO/FROM OTHER ELECTRONICS ON YOUR VESSEL.

Works on most marine HF transceivers including ICOM M700, M710, M800, M801, M802, M810, GM800 HF Transceivers up to 60 MHz. Also applicable to SEA 225 & 323, Furuno FS 1502, SGC SG-2000 and similar HF marine radios with external antenna tuners.

Purpose. The RFI kit is designed to be installed on your radio transceiver to reduce Radio Frequency Interference (RFI) caused by common mode current on the outside of the coax braid at the output of your radio and AC/DC power cable and antenna tuner cable.

This kit will help reduce or eliminate:

1. “Hot mic” RFI caused by poor grounding of antennas or common mode currents from linear amps feeding unbalanced (coax fed) antennas without baluns/line isolators.

2. RFI to other electronic devices including audio/video systems, computers, marine electronics, etc.

A side benefit is a reduction in noise floor in your receiver depending on the amount of noise being introduced by common mode currents (which are blocked/reduced by the chokes in this kit).

These chokes use a special mix of ferrite core material that is effective in suppressing radio frequency interference from transmitters and high noise floor on receivers.

The split beads beads are easy to use, don’t require modification of the protected equipment and work in almost all cases, even when plug-in filters fail.

Use of the chokes often helps cure SWR problems between transceiver and antenna tuner s used on marine systems. The DC power line choke helps keep common mode current out of the power line which could cause interference to other devices connected to the same power line if not suppressed.

Included are the following chokes and installation guidelines:

RF Input/Output: Antenna feed line choke installed between radio and antenna tuner coax to reduce noise into receiver and suppress RFI. Includes double barrel male connector for joining choke directly to antenna tuner.

DC Input: 1.4" inside diameter filter ring – coil 3-7 turns of DC power cable through center

Antenna tuner cable: Two 1/2 snap on for 1-2 turns through center at each end of cable.
Save this product for later
Display prices in: USD

Likewise Termination Resistor values vary from 500-1250 ohms and we have a good selection shown HERE: