Broad Band Terminated Dipoles (BBTD), Tilted Terminated Fold Dipoles (T2FD) and Balanced Termination Folded Dipole BTFD) antennas can be designed to cover a large range of frequencies between 1.8 30 MHz. Longer length antennas generally provide better low frequency efficiency but take up a larger footprint of land. One BBTD that has worked well at the AK6R antenna farm is shown below. Many other designs are available and can be found at www.HFLINK.COM as well as other internet sites. Your mileage may vary using this antenna, but as a general coverage antenna for ham and shortwave broadcast, the simplicity can’t be beat even though an individual dipole on a specific band may out perform this broad band dipole. Palomar Engineers has all the parts you need to build this antenna, so why not give it a try?
Depending on the source of the antenna design, different value baluns are specified. Our Bullet(TM) baluns in ratios of 9:1, 12:1 and 16:1 are excellent for this type of antenna as they are broadband from 1.8-61 MHz and will take up to 500 watts PEP.
Coax Common Mode Noise Filter
Common mode current induced by radiated sources (plasma TV, routers, computers, transmitters, etc) can be picked up by the outside of the coax braid from the antenna feed point back to the receiver. This portion of the coax braid acts like a receiving antenna, picking up common mode noise signals that override weak signals making them difficult or impossible to hear!
The solution? A common mode noise filter with high choking impedance at the receiver end of the coax.
Do you have common mode noise on your coax? Here is a simple test (pdf)
1. Remove the coax connector and measure the noise level.
2. Now insert the coax connector CENTER CONDUCTOR ONLY into the SO-239 antenna input and measure
the noise level (it should be higher and include possible signals)
3. Now connect the OUTER SHELL of the coax connector to the antenna input and measure the noise
level. If it is higher you have common mode noise and the common mode noise filter will help suppress this noise which
is carried on the outside of the coax braid (acting as a second receive antenna).
Common mode noise suppression with the Palomar CMNF series of filters is typically 25-36 dB which is equivalent to 4-6 “S” units on radios with 6 dB/”S” unit or may be more on radios with 3dB/”S” unit.
Note for antenna switch users, perform the above test on each antenna coax lead separately to determine if that particular antenna braid is contributing noise to the receiver – use a coax noise filter on the antennas that have common mode noise.
![Broad Band Terminated Dipoles (BBTD, T2FD) 3862217729 - Broad Band Terminated Dipoles (BBTD, T2FD)](https://i0.wp.com/d2j6dbq0eux0bg.cloudfront.net/images/10325621/3862217729.jpg?ssl=1)
![Broad Band Terminated Dipoles (BBTD, T2FD) 4493391010 - Broad Band Terminated Dipoles (BBTD, T2FD)](https://i0.wp.com/d2j6dbq0eux0bg.cloudfront.net/images/10325621/4493391010.png?ssl=1)
![Broad Band Terminated Dipoles (BBTD, T2FD) 4222605656 - Broad Band Terminated Dipoles (BBTD, T2FD)](https://i0.wp.com/d2j6dbq0eux0bg.cloudfront.net/images/10325621/4222605656.png?ssl=1)
![Broad Band Terminated Dipoles (BBTD, T2FD) 3567278249 - Broad Band Terminated Dipoles (BBTD, T2FD)](https://i0.wp.com/d2j6dbq0eux0bg.cloudfront.net/images/10325621/3567278249.jpg?ssl=1)
Likewise Termination Resistor values vary from 500-1250 ohms and we have a good selection shown HERE: