AM Broadcast RFI Kits

Slip On Feed Line Choke/Isolator - 1/4"/6mm coax cable, RG-58/LMR240, 1-100 MHz

SKU SLO31-1/4-5
$17.95
On Sale
List price $24.95
Save 28%
Bulk pricing available for quantities of 2 units or more
Select # of beads
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$15.9511% off
10 items$12.9528% off
Save this product for later
Share this product with your friends
Slip On Feed Line Choke/Isolator - 1/4"/6mm coax cable, RG-58/LMR240, 1-100 MHz
Product Details
UPC: Does not apply
Brand: Palomar Engineers
MPN: SLO31-1/4-5, -10, -15 - old part # is BA-58-5, -10, -15
Effective Frequency Range (MHz): 3-300 (5 bead), 1.8-300 (10, 15 bead)
PEP Power Rating (watts): same as coax cable rating
Choking Impedance Range (ohms): 5 bead: 500-1300, 10 bead: 600-1800, 15 bead: 1000-2100
Common Mode Attenuation (db): 5 bead: 16-22 db, 10 bead: 17-25 db, 15 bead: 21-27 db
Estimated Insertion Loss (db): .025
Input Connector Type: none
Output Connector Connector Type: none
Ground Connector (Y/N): none
Enclosure Size (LxWxH inches): none

Includes protective heat shrink

1/4″/6.4mm max Cable Size Chokes

For use with RG-58, RG-6, RG-59, LM-240 and similar size cables – all cable impedances, 160-6 meters. Choke diameter 0.6 inch. Requires 9-1/2 inches of cable for installation of SLO-1/4.Choose SLO-1/4 (5 beads) or for extended choking, choose SLO-1/4-10 (10 beads) or for super extended choking choose SLO-1/4-15 (15 beads).Use SLO-1/4 on RG-6 to stop RFI on cable/satellite systems.


Select chokes with minimum of 500 ohms at your frequency of interest for best results or upgrade to our CUBE(TM), or Super Choker(TM) or Maxi-Choker(TM) chokes up to 10,000 ohms choking

Use on RG-6 coax to stop RFI on cable/satellite systems.

Select 10 bead version for 160 meter use, 15 bead version for even higher choking power.

Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options.

This product was previously named BA-58

When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI