AM Broadcast RFI Kits

FSB31-1-1, ID=1", RFI Range 1-300 MHz

SKU FSB31-1-1
$19.95
Bulk pricing available for quantities of 2 units or more
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$17.9510% off
Save this product for later
Share this product with your friends
FSB31-1-1, ID=1", RFI Range 1-300 MHz
Product Details
MPN: FSB31-1
Initial Permeability (@ 10KHz): 1500
Material: MnZn
Max cable size - in/mm: 1.0/25.4
OD (A) - in/mm: 2.22/56.4
ID (B) - in/mm: 1.02/25.9
Length (C) - in/mm: 1.69/41.9
Z (ohms per bead - single turn 1 MHz): 45
Z (ohms per bead - single turn 5 MHz): 90
Z (ohms per bead - single turn 10 MHz): 125
Z (ohms per bead - single turn 25 MHz): 218
Z (ohms per bead - single turn 100 MHz): 375
Z ohms (per bead - single turn 250 MHz): 340
Case/Box lot size: 36

Also known as Big Clamp On. Very useful for AC/DC power, coax cable, etc. Use multiple turns for best results or multiple chokes in series (recommended for large amperage power cables). Always put +/- dc cables through the same ferrite filter so their fields cancel and the ferrite suppresses the common mode current on each cable.

These ferrites also work well for coax feed line chokes. Use 3 turns of RG-213 size coax thru center and put several ferrite in series each with 3 turns to make an excellent 80-10 meter high power feed line choke.

When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI