Coax Common Mode Noise Filter - 1500/5000 Watts, 100 KHz to 30 MHz, up to -38 dB Common Mode Noise Suppression!

Name: Coax Common Mode Noise Filter - 1500/5000 Watts, 100 KHz to 30 MHz, up to -38 dB Common Mode Noise Suppression!
SKU: CMNF-1500LF
Price: 89.95 USD
Availability: InStock

CMNF-1500LF

$89.95

In stock

Quantity:

Product Details

MPN: CMNF-1500HF

Type: NEW

Country/Region of Manufacture: United States

Filter Power Rating (PEP watts): 1500

Choking Impedance (ohms): 1000-6500

Common Mode Attenuation (db): 21-36 db

RFI Suppression Range (MHz): 1.8-60

Insertion Loss (db): .05

# Ferrite Filters: 5

Enclosure Size (inches): 4" x 4" x 2"

Typical Use:: Noise filter at radio end of coax between amplifier and antenna tuner

CMNF-1500LF for transmitter/receiver coax lines up to 1500 watts PEP - 100 KHz - 12 MHz, Up to -38 dB Common Mode Noise Suppression!

For coax feed lines with receive and transmit signals, you will love the small size, wide frequency range and excellent attenuation of common mode noise interference

- Reduces broadband common mode receiver noise* picked up on the outside of the antenna coax feed line.

- Wide frequency range works on all brands of radios and coax fed antennas from 200 KHz to 7 MHz

- Common mode noise rejection up to 20-36 DB (3-6 "S" units) depending on frequency

- Simple plug & play installation: plug a short jumper from the CMNF-1500LF to your amplifier output and plug the feed line (or a jumper to your antenna tuner) into the other SO-239 CMNF-1500LF input. Either connector can be input or output. Rated at 1500 watts PEP.

- will work with Bias-T antenna switches and will pass DC voltage from input to output with no attenuation

* not effective for noise from AC power lines or noise received directly by antenna

Installation Note: For best results, and to reduce co-interference between choked and unchoked coax feed lines with multiple antennas, ALL antenna feed lines entering the radio room need to have a separate feed line choke particularly if they are at a different frequency then HF, like VHF or UHF.

If you use a antenna switch for multiple antennas in the .2-7 MHz range, place the CMNF-1500LF in the "common" line of the antenna coax switch and the antenna tuner/amplifier.

Got Common Mode Noise? Not Sure - Find out now by clicking link below:

Palomar Engineers Common Mode Noise on Coax User Diagnosis Test

Save this product for later

When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes. Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas. Consequently it takes a large antenna to receive the signals. Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc. The device wires that connect to these “antennas” need to be choked with as many turns through the ferrite as possible. Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular. Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance. Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).