AM Broadcast RFI Kits

CUBE Feed Line Choke/Line Isolator Unun, 1.5KW, 1.8-65 MHz, -38dB Suppression

SKU CU-1-1500SO
$109.95
On Sale
List price $149.95
Save 27%
Bulk pricing available for quantities of 2 units or more
Single Side Input/Output
Input/Output Connectors
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$104.955% off
10 items$94.9514% off
50 items$89.9518% off
100 items$84.9523% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
CUBE Feed Line Choke/Line Isolator Unun, 1.5KW, 1.8-65 MHz, -38dB Suppression
Product Details
Brand: Palomar Engineers
Effective Frequency Range (MHz): 1.8-65 MHz
PEP Power Rating (watts): 1500
Estimated Insertion Loss (db): .10
Input Connector Type: SO-239 female
Output Connector Connector Type: SO-239 female
Ground Connector (Y/N): none
Enclosure Size (LxWxH inches): 4 x 4 x 2

1500 Watt Rated 1:1 CUBE™ Unun

Th CU-1-1500 unun is useful as common mode feed line chokes or coax to antenna interfaces. SO-239 output models can also be used with balanced antennas if a short coax cable “pigtail” is used on the output and connected to the antenna. Rated 1500 Watts PEP from 1.8-61 MHz.

Use as line isolator, antenna interface, or as a common mode choke to keep RF on the antenna and off the outside of the coax braid.

Much more effective then our sleeve feed line chokes due to our exclusive Multimix(TM) multi-core topology using high permeability ferrite cores which provides a high choking impedance over a broad frequency range.

Typical common mode suppression is 20-38 dB (up to 6 "S" units) from 1.8-61 MHz reduces common mode current! For most effective results, use 1 choke at the antenna and another at the radio. Helps reduce noise floor too by choking off common mode neighborhood noise picked up on outside of coax braid.

Optionally available with both input and output on same side for certain installations and wall mounts available on each side for both models.

Choose SO-239 UHF or N connector input/output connectors

When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI