AM Broadcast RFI Kits

Bullet 50:200 (4:1) HF Balun, 1.8-61 MHz, 500/1500 Watts PEP, Loop, OCF, ZEPP

SKU Bullet-4B-500EB
$89.95
Bulk pricing available for quantities of 2 units or more
PEP Power Rating
1
Buy more, save more
QuantityPrice per itemDiscount
2 items$79.9511% off
Save this product for later
Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in
Share this product with your friends
Bullet 50:200 (4:1) HF Balun, 1.8-61 MHz, 500/1500 Watts PEP, Loop, OCF, ZEPP
Product Details
Country/Region of Manufacture: USA
Type: NEW
Input ohms/Output ohms: 50 in, 200 out
Frequency Range < 2:1 SWR (MHz): 1.8-61
PEP Power Rating (watts): 500/1500
Input Connector: UHF SO-239
Output Connector(s): Eyebolt/Wingnut
Transformer Topology: Broadband
Hardware Type: Stainless - 1/4"
Antenna Compatability: OCF, Zepp, Folded Dipole, Loop

The Bullet-4B-500 and SBullet-4B-1500 are multi-core core baluns with a compact enclosure (looks like a bullet) enclosure that is physically lightweight but electrically robust and easy to transport for your portable loop antenna solution or permanent installation. Halyard hoist at top of balun for convenient attachment point. Input is via SO-239 coax connector and output with side eye bolt output. Choose your model rated 500 or 1500 Watts PEP from 1.8-61 MHz.

This transformer requires a feed line choke (see related products) to isolate the coax feed line from the antenna. A coax noise filter at the radio end of the coax is also recommended for best results.

Vertical Delta Loops

Multi-band vertical delta loops can be oriented several way but the most popular is to have the “pointy” end at the top (usually a single support) and the lower horizontal ends just out of reach of humans and animals. Best feed point at the top for multi-band use with a 4;1 balun. CUt total wire length to 1005/F (MHz) where F is lowest band frequency of use..

Single band vertical delta loops are best fed 1/4 wavelength (246/f(MHz)) from the top point down one side. Vertical delta loops use the same 2:1 baluns as the horizontal loops.

NOTE: We rate our Bullet baluns (and ununs) VERY conservatively at 500 watts PEP with a 50% duty cycle. Some manufacturers selling low cost baluns may use a 5% duty cycle for their PEP rating to make it appear you get a higher rated balun for a lower price, but you may in fact be getting be getting less. Their 1500 watts PEP really means 75 watts continuous or 150 watts at a 50% duty cycle compared to our 250 watts at 50% duty cycle. Our baluns typically cover a larger frequency range under 2:1 SWR which make your transceiver happy and probably will last longer with less electrical stress.

Remember we over engineer our products, to out perform our competition - just compare the weight of our baluns to theirs and you will know we put much more into our products so you don't have to worry about failure at a critical moment.


When considering solutions for AM broadcast (550 Khz – 1.8 Mhz) you should consider Mix 77 ferrites available in a variety of shapes and sizes.  Choose a size to give the maximum number of turns of the affected wire or cable.

AM broadcast transmits on a low frequency with large antennas.  Consequently it takes a large antenna to receive the signals.  Typical “antennas” are AC house wiring, phone lines, long satellite or cable TV cables, DSL/CAT5 lines running between rooms, etc.  The device wires that connect to these  “antennas” need to be choked with as many turns through the ferrite as possible.  Some installation examples are shown below on this page.

For AC/ DC power cords and coax cables the F240-77 (2.4″ OD, 1.4″ ID) “Donut” toroid is the most popular.  Also available are smaller toroid donuts and Mix 77 beads. Shown below is a graph with 8, 10, and 12 turns through the toroid – obviously more turns has higher choking impedance.  Mix 77 toroid products are HERE and Mix 77 small beads (for small wires) are HERE

F240 77 Turns Comparison 1024x648 - AM Broadcast RFI Kits

F240-77 Turns Comparison from .1 – 8.1 Mhz

Shown below is a graph of frequency response verses choking magnitude for a F240-77 in the AM Broadcast band for a 12 turn coil around the toroid. (Same info as above but different frequency range).

AM Band Choking Graph F240 77 1024x648 - AM Broadcast RFI Kits

F240-77 Choking Impedance in AM Broadcast Band

 

 

Typical Installations for Donut/Ring Toroids

20131210 114716 150x150 - AM Broadcast RFI Kits

AC Cable on F-240 Toroid – 6 turns

20131210 115137 150x150 - AM Broadcast RFI Kits

Ethernet Cable on F-240 Toroid – 7 turns

20131222 125533 150x150 - AM Broadcast RFI Kits

Audio or Mic cable on F240- 12 turns

 

 Extra Mix 75 Snap On Beads  HERE – VERY effective for AM Broadcast RFI