For 1/2” cables use five split beads for 80-10 meters (3-30 MHz) or ten split beads for 160-10 (1.8-30 MHz) meters or use 15 for even higher choking for 1-10 MHz. For 144 MHz use only 4 beads as they will provide > 500 ohms. Typical common mode suppression is -9 to 30 dB depending upon the number of beads and frequency. Quite often 20 dB is considered the minimum effective reduction. A minimum impedance of 500 ohms is needed for 50 ohm cable or 10 times the cable impedance for other cables to make a measurable difference in common mode current suppression. The beads clamp to the cable and may be operated as is for indoor use. However, it is strongly suggested that they be covered to protect the plastic covers from weathering – use electrical tape for best results or heat shrink to ensure longer life. All kits come with instruction manual which covers assembly and application tips. As you can see from the impedance vs frequency graph, you can very effectively increase the choking impedance by increasing the number of beads on the cable. Snap On and Slip on Feed line chokes available in sizes to fix cables with outside diameters of 1/4", 3/8", 1/2", 3/4", 1" - check website for other size options. tech note: For RFI frequencies below 3.75 MHz, choose SNO75-1/2-5, 10 or 15 for improved common mode rejection Note: Ferrite beads may be hexagonal or square shape depending on inventory on hand at time of order.
Use for 1/2″ Cable – RG8, RG213, LMR-400, etc.
Typical Impedance per split bead: 10 MHz: 90 ohms, 25 MHz: 156 ohms, 100 MHz: 250 ohms, 250 MHz: 305 ohms
Iron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:
Turns = 100 x 
Toroid Dimensions
To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.
All iron powder cores are special orders. Please allow one week for shipment after order received.
The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1 and 9;1 very high power transmission line transformers.
For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.
For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:
T200A x 2 = 1.5KW
T300A x 2 = 2.5KW
T400A x 2 = 5KW
Use Mix 2 for all the above transmission line transformers. Fully assembled and enclosed units are available for each of the power levels. Click HERE for information.
4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections
For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz. Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz. For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.
Minimum order for iron powder cores is $50
Shipping on larger cores in quantity may be more than $10 – email/call for quote.