Each end fed antenna needs a feed line choke at the radio end of the coax to stop the antenna common mode current (on the coax braid) from getting into the radio when transmitting and also to stop RFI common mode noise when receiving. A Add the Feed line choke (part # SOFLC) to your end fed antenna today today and stop the pesky RFI from getting into your radio and causing RFI, audio distortion or unexpected operation! NOTE: Coax shown in picture is NOT INCLUDED and is shown as an installation example only. If you want a pre-wound choke check part# JC-1-1500-3 or JC-1-1500-6. For non-resonant end fed antennas placement of the choke from 10-50 feet away from the antenna feed point to use the coax braid as the counterpoise (since these antennas are really off center fed dipoles with the short side using the coax braid as the count5erpoise. Wind 8-10 turns thru center for an effective 3-30 Mhz choke. For End fed Half Wave antennas place 3-10 feet from antenna feed point to act as short counterpoise for these voltage fed antennas. Use 8-10 turns. TECH NOTE: SNAP On Chokes for 80 and 160 meter end fed antennas If you use RG-8X size cable, use 2 SOFLC if you have 5-6 turns thru the center of each.See picture on left as an example of how to wind the cable.
Measure 40 feet from the matching unun and then wind 6 turns thru the center of the SOFLC.Close it up and then wind an additional 6 turns thru another SOFLC placed adjacent to the first one and on the radio station side of the coax.See picture to left. If you use LMR-400 or 1/2" coax cable you will only get 3 turns thru the snap on choke and you will need an additional choke (with an additional 3 turns) in series to provide enough choking on 40 and 80 meters. Part# SOFLC.
In lieu of the 2 chokes shown above, you may also use a F400-31 ring (3” ID) with 6 or more turns which provides a much higher common mode suppression and better antenna tuning on 80 meters. See picture for winding example. 
SNAP On Feed Line Choke
simple easy to adjust in different places along the coax used as a counterpoise is the snap on ferrite core with a 1" ID (hole) installed as shown in the picture. (coax not included, but you can use RG-8X size for 5 turns and RG-8X size for 3 turns).
$19.95
Iron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:
Turns = 100 x 
Toroid Dimensions
To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.
All iron powder cores are special orders. Please allow one week for shipment after order received.
The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1 and 9;1 very high power transmission line transformers.
For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.
For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:
T200A x 2 = 1.5KW
T300A x 2 = 2.5KW
T400A x 2 = 5KW
Use Mix 2 for all the above transmission line transformers. Fully assembled and enclosed units are available for each of the power levels. Click HERE for information.
4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections
For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz. Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz. For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.
Minimum order for iron powder cores is $50
Shipping on larger cores in quantity may be more than $10 – email/call for quote.