The simplest, most cost effective feed line choke is a ferrite ring installed as shown in the picture (at the antenna feed point) to stop feed line radiation or at the radio end of the coax to suppress common mode coax noise current on the coax braid. Improves antenna pattern by preventing your dipole from becoming a tripole Suppresses pesky coax braid radiation and RFI Reduces coax braid common mode current up to -30 dB ( 6 "S" units) on receive Use one choke for each antenna feed line Add a double female barrel connector to act as an "extension" of the existing coax. Magnetic Loop Users: use 1 JC-1-1500 at the antenna feed point to keep all of transmit power on antenna and another at radio end to remove common mode noise received on the coax braid. Need the ring only and not the jumper, select F240-31-1 as the part #. Question: Assuming the JC-1-1500 uses mix 31, why is the effective range 1.8-65MHz instead of 1-300MHz? Answer: Look at measurement chart to see the answer - it takes at least -12 dB of common mode rejection to see/hear a noticeable difference with and without choke. Yes the spec for mix 31 say it is good to 300 mhz but at that frequency the CMRR is very small and hasn't much of effect on common mode rejection. Also when you form a choke with coax your are actually creating a parallel tuned circuit at a certain resonant frequency determined by the coax capacitance of approximately 28 pf/foot and the inductance of the coil. The graph shown that the max CMRR is roughly -30 dB between 1-21 MHz and slightly less as you go higher in freq (the resonant freq of the JC-1-1500 is roughly 10 MHZ and broad banded by the use of the ferrite). Above 6 meters CMRR becomes low so as not to be very effective. If you want to use the choke on higher bands you need to change ferrite mix and the number of turns of the choke so the center resonant freq is higher. Ferrite are in reality frequency dependent resistors and the specs say they have a resistive component above 1 mHz and under 300 mHz but the resistance (or CMRR) has to be high enough to be effective. We publish the effective range so you know what to expect when used.
Simple Jumper Feed Line Choke
$19.95
Iron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:
Turns = 100 x 
Toroid Dimensions
To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.
All iron powder cores are special orders. Please allow one week for shipment after order received.
The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1 and 9;1 very high power transmission line transformers.
For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.
For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:
T200A x 2 = 1.5KW
T300A x 2 = 2.5KW
T400A x 2 = 5KW
Use Mix 2 for all the above transmission line transformers. Fully assembled and enclosed units are available for each of the power levels. Click HERE for information.
4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections
For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz. Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz. For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.
Minimum order for iron powder cores is $50
Shipping on larger cores in quantity may be more than $10 – email/call for quote.