PURPOSE:The N-25 is a passive noise suppressor that employs a high density, low loss toroid 0.25mH choke designed to eliminate in-line noise for Auto-sound, Avionics, and ham radio/CB/Two-Way communication systems including: Alternator Whine, Fan Hums, Dodge Ram Cummings Torque Converter Clutch Cycling Repair*, etc.The N-25 applications include Power Equalizers, Small Amplifiers, Cellular Phones, CB Radios, Two Way Communication Equipment, CD Players, and AM/FM Cassette Decks, etc. FEATURES:The air-cooled design of the N-25 filter permits maximum efficiency and effectiveness.The ferrite toroid core of the choke component of the L configuration is responsible for a very high rate of attenuation with very low line losses.There are only three wires needed for the installation of the passive filter -Filter Input, Filter Output, and the Chassis Ground. INSTALLATION:Make sure the noise is in-line before installing an in-line filter such as the N-25.A good confirmation would be to temporarily substitute a 120 VAC to a 12 VDC power supply, or a 12 Volt motorcycle battery, for the vehicle's electrical system.If the noise goes away when the alternate power supply is connected, then you have a case of in-line noise. To get optimum results with the N-25, the following directions should be followed: 1.Cut the component's main power lead between the fuse and the component. 2. Connect the Green wire to the fuse side. (If there is no fuse, add one --- 10 Amps is recommended) 3.Connect the fused Red wire to the component side. 4.Connect the Black wire to a good chassis ground. Practical and easy to install, the N-25 is one of the most versatile and effective filters on the market. Note: The 30-Amp rating is instantaneous = peak… not constant. Fuse the Green lead with a 5 to 10-Amp fuse. Average current draw should be no larger than the fuse size of 10 amps.
Iron powder cores are more stable than ferrites and do not saturate as easily so they are best for tuned circuits, filters, and high power inductors. They come in different “Mixes” for use at different frequencies. For best “Q” use the Mix specified for your frequency.To find the number of turns to give the desired inductance for your coil use the formula below:
Turns = 100 x 
Toroid Dimensions
To order specify core size and mix (e.g. T200A-2). Available in sizes that have µH per 100 turns shown in table.
All iron powder cores are special orders. Please allow one week for shipment after order received.
The iron powder cores shown in the above tables are primarily used for either high power feed line chokes for common mode current reduction or for 4:1 and 9;1 very high power transmission line transformers.
For high power feed line chokes, choose the inside diameter of the iron powder core closest to the transmission line outside diameter and use 6-20 cores at the junction with the antenna feed.
For 4:1 (50/200 or 75/300 ohm) transmission line transformers in the range of 1.8-30 Mhz, select the size appropriate for the power level as follows:
T200A x 2 = 1.5KW
T300A x 2 = 2.5KW
T400A x 2 = 5KW
Use Mix 2 for all the above transmission line transformers. Fully assembled and enclosed units are available for each of the power levels. Click HERE for information.
4:1 transmission line transformers using iron powder cores are typically used for ladder line to 50 ohm coax connections
For .1 – 2 Mhz wide band transformers use Mix 26 which has a higher permeability and requires less turns to achieve a given inductance. Mix 2 has almost constant permeability from 1-30 Mhz. Mix 26 has an initial permeability of 75 at .1 Mhz and gradually decreases to about 10 at 30 Mhz. For high power AM broadcast range (.5-1.7 Mhz) transformer, use Mix 26 to reduce the turn count.
Minimum order for iron powder cores is $50
Shipping on larger cores in quantity may be more than $10 – email/call for quote.